To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *35764 (-10)
  legOS and QNX
 
I got two simple questions: 1. Anyone tried to compile legOS & LNPD Deamon under QNX. 2. Anyone tried to comunicate with LNPD from other computer, tcp/ip? (i mean exactly: QNX <-> linux (LNPD here) ) pleasy send me any adresses or information Tomasz (...) (24 years ago, 11-Dec-02, to lugnet.robotics)
 
  Lego® Technic Motor (43362) internals
 
I received two new 9V mini-motors from S@H, that was of the new variety described by Mark Riley ((URL) lead me to remove back cover, but it was wired to the rest of the motor. So I put it back in place... no luck, the motor didn't turn any more :c( (...) (24 years ago, 11-Dec-02, to lugnet.robotics, lugnet.technic)  
 
  Re: BrickOS
 
Thanks for posting the link. I've been looking for something like this, but didn't know this particular thing existed. Now I just have to wait 2hrs 25min while it downloads! God I love sipping the internet through a straw... Matthias Jetleb (24 years ago, 11-Dec-02, to lugnet.robotics)
 
  Re: Spybotics Comms
 
(...) You already have an RCX 2.0. Aside from printing "RCX 2.0" on the plastic, the RCX in RIS 2.0 is identical to the one included in RIS 1.5. Since you have downloaded the 2.0 firmware, you should be all set. Dave (24 years ago, 11-Dec-02, to lugnet.robotics.spybotics)
 
  Re: Spybotics Comms
 
(...) Hi Mark, am I right, all you have described above only works with a RCX2.0-hardware cause of the changed IR-interface? Is there any chance to communicate between Spybot and RCX1.5 (with 2.0 firmware)? If there is no, I will have to buy a (...) (24 years ago, 10-Dec-02, to lugnet.robotics.spybotics)
 
  Re: Firmware download troubles
 
(...) Look at Edit/Preferences. On the General tab is a checkbox labeled "Use fast mode when downloading firmware" You can uncheck that option to use normal speed firmware downloads via BricxCC. John Hansen (URL) (24 years ago, 10-Dec-02, to lugnet.robotics.rcx)
 
  Re: Firmware download troubles
 
The low buzz tone is an error generated by the ROM firmware for failure condition detected as part of the "unlock firmware" opcode. There are two causes of this. [1] ROM software calculates a checksum value of the downloaded firmware and this (...) (24 years ago, 10-Dec-02, to lugnet.robotics.rcx)
 
  Re: Firmware download troubles
 
(...) ... (...) Dick and others, Thanks - this helped. What I did to solve this was run the NCQ command-line download at "normal" speed. This worked the first time. Interestingly, I am not sure that the Bricx (v3.3) download was running quad speed (...) (24 years ago, 10-Dec-02, to lugnet.robotics.rcx)
 
  Re: Firmware download troubles
 
A likely explanation for your downloading problem is the following. Standard Lego software uses 2400 baud data rate and a protocol that sends "double" bytes. The "double" byte is that each data byte is followed by its complement. Alternative (...) (24 years ago, 10-Dec-02, to lugnet.robotics.rcx)
 
  Re: want to get inentors kit but...
 
(...) If you want to use the 'official' Lego software, then I'm not sure what Windoze OS's are supported - but certainly Linux isn't. However, many (most even?) serious users end up using a 3rd party software package called 'Not Quite C' (NQC) which (...) (24 years ago, 10-Dec-02, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR