 | | Re: Lost my IR tower
|
|
Hi Thorn Family I would like to see the diagram. I'm told it's at (URL) can email it directly if it's not there. Peter (23 years ago, 14-Feb-02, to lugnet.robotics)
|
| |
| | Re: How communication is handled
|
|
hi Rob, (...) here is some information about IR-tower/communication, also check Kekoa's site mentioned below (URL) (...) check the site of Kekoa (URL) (...) Stef Mientki (23 years ago, 14-Feb-02, to lugnet.robotics)
|
| |
| | RE: How communication is handled
|
|
the better way to know how the IR work is the legOS kernel source. I read it and see that legOS use IRQ for transmiting and receiving message. When legOS receive a message he see first if the activity of the IR transmitter is not true. Then he call (...) (23 years ago, 14-Feb-02, to lugnet.robotics)
|
| |
| | How communication is handled
|
|
Hello everyone! Does anyonk know what the RCX does with IR data it sees from the IR module when it is busy transmitting? I've set the RCX in a situation where I know the IR it was sending could be seen by it's own IR detector, yet it didn't appear (...) (23 years ago, 14-Feb-02, to lugnet.robotics)
|
| |
| | Re: Lost my IR Tower
|
|
(...) It's probably easier to solder the wires on without the diodes. They could probably be put back on easily though. (23 years ago, 14-Feb-02, to lugnet.robotics)
|
| |
| | Single set Technic Power Pulling.
|
|
FUT: lugnet.technic Hi! Here's yet another Tehnic genre booster! Challenge: Build a model that can pull as much load as possible using pieces from _only_one_ official LEGO set! One class for each set so you can all be winners, no matter what set you (...) (23 years ago, 14-Feb-02, to lugnet.technic, lugnet.announce, lugnet.build, lugnet.general, lugnet.robotics)
|
| |
| | Challenge: Technic Model of the Month!
|
|
FUT: lugnet.technic Hi all! I've decided the Technic genre needs a boost so I have made a Technic model of the month competition/challenge similar to ldraw.org's MOTM & SOTM. Each month a winner will be elected by an e-mail voting process. For more (...) (23 years ago, 14-Feb-02, to lugnet.technic, lugnet.announce, lugnet.build, lugnet.general, lugnet.robotics)
|
| |
| | Re: Power to RCX
|
|
(...) Yes, but any regulator would convert power uselessly into heat, probably too much if you use a much higher voltage and draw some current. It would be better to use higher voltage motor controllers directly (if they exist). And of course this (...) (23 years ago, 14-Feb-02, to lugnet.robotics.rcx)
|
| |
| | Re: Power to RCX
|
|
(...) Utter nonsense until you destroy the controller itself. Remember, while the Lego motors can take a fairly substantial voltage without being destroyed, the same is not true of the motor controller within the RCX. There is a voltage limit for (...) (23 years ago, 14-Feb-02, to lugnet.robotics.rcx)
|
| |
| | Re: Palm IR to RCX
|
|
"Till Harbaum" <lego-robotics@crynwr.com> wrote in message news:200202131831.g1....uka.de... (...) <<snip>>. (...) The remote is a one way only messaging scheme. It sends a "standard" RCX message of opcode 0xD2 and two data bytes. The two data (...) (23 years ago, 14-Feb-02, to lugnet.robotics)
|
