 | | Re: Unable to compile helloworld.c
|
|
(...) <sigh> I'm not sure either. Actually no idea so far. It seams that makelx is called with wrong parameters. But why? Did you successfully made the demos in the demo dir? (...) That puzzles me, too. The compiler and the binutils come as a rpm (...) (25 years ago, 5-Nov-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Unable to compile helloworld.c
|
|
Well!I looked in the makefile and couldn't see anything wrong with the path.As for having legOS under usr/lib, it was done at the time of installing the rpm and I hadn't specified any path.Now,I tried copying config.h and putting it in the 'include' (...) (25 years ago, 5-Nov-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: visible terminals and stringing modifiers
|
|
(...) Robolab 2.5 makes wiring even easier with auto-wire. If you place an icon close enough to the END on the right side of an icon, the new icon will be automatically wired in. This also applies to modifiers. If a modifier is placed closely to the (...) (25 years ago, 5-Nov-01, to lugnet.robotics.rcx.robolab, lugnet.dacta)
|
| |
 | | Robolab 2.5
|
|
Have a look at an implementation of a subsumption architecture to Robolab 2.5 at (URL) 2.5 seems very powerful. The developpers have overcome a lot of limitations that were still present in version 2.0 Specially, you may now operate indirect (...) (25 years ago, 5-Nov-01, to lugnet.robotics)
|
| |
 | | Re: Unable to compile helloworld.c
|
|
(...) The error messages state that helloworld includes conio.h which tries in line 41 to include config.h. Helloworld includes unistd.h which includes time.h which tries in line 32 to include config.h. So, conio.h, unistd.h and time.h are found, (...) (25 years ago, 5-Nov-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Installing Vision Command on Windows 2000?
|
|
"Carlo Ottolina" <kruntz@tiscalinet.it> wrote in message news:GMBqDG.FqC@lugnet.com... (...) nice (...) I download the drivers and installed them, but W2K reports a code 10 problem "device cannot start". I've also tried installing the drivers from (...) (25 years ago, 5-Nov-01, to lugnet.robotics)
|
| |
 | | Problems with ControlLab interface and LabView
|
|
Hi there Is there someone who knows a lot about Dacta ControlLab interface and LabView / Lego Engineer? I've got a problem. When using a standard or a geared Lego 9V motor with the voltage regulator of the train system, I can adjust speed in six (...) (25 years ago, 5-Nov-01, to lugnet.robotics.rcx.robolab)
|
| |
 | | Re: Installing Vision Command on Windows 2000?
|
|
"Daniel Crichton" <danielc@helio.co.uk> wrote in message news:GMBnvI.Axt@lugnet.com... (...) says (...) Unfortunately, installing Vision Command on W2K is really a #@#£$£ job. I did it once (manual inst., using W98 machine diffs as an example...), (...) (25 years ago, 5-Nov-01, to lugnet.robotics)
|
| |
 | | Installing Vision Command on Windows 2000?
|
|
Is it possible to install the Vision Command software on Windows 2000? It keeps refusing to install on my SP2 machine, yet there are Windows 2000 drivers on the CD. I can run the setup from the QuickCam folder and it says that there are missing (...) (25 years ago, 5-Nov-01, to lugnet.robotics)
|
| |
 | | Does RL2.5 have array support?
|
|
All -- I'm just getting to grips with RL2.5 (been using NQC prior to this) so apologies that this is a total newbie question. The documentation is, ummmm, skimpy on a number of advanced topics (e.g., LASM support). I'm trying to figure out if (...) (25 years ago, 5-Nov-01, to lugnet.robotics.rcx.robolab)
|