To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *29764 (-20)
  Re: Cybermaster alternative software
 
(...) NQC yes (memory is very limited), anything that replaces firmware (lejos, legos, forth, ...) no. Jürgen (25 years ago, 7-Sep-01, to lugnet.robotics.cybermaster)
 
  RE: Cybermaster alternative software
 
Cybermaster's firmware's on *ROM* so you're limited to tools that use the standard firmware. That excludes the likes of legOS, pbForth, etc. You can use NQC in Cybermaster "mode" or any other language/tool generating standard firmware byte-codes. (...) (25 years ago, 7-Sep-01, to lugnet.robotics.cybermaster)
 
  Re: Anyone know how to build a stall sensor?
 
Paul, If you put a small lamp in serie with the motor , you can monitor the current drawn by thr motor through a lightsensor. The more current the more the light, there is only one thing you have less motorpower. Gretings, Rik "Paul Andrews" (...) (25 years ago, 7-Sep-01, to lugnet.robotics.rcx)
 
  About SetSerialComm(SERIAL_COMM_DEFAULT);
 
Hi, Dave In your NQC Guide, there is a text about this function "The default is to send data at 2400 baud using a 50% duty cycle on a 38kHz carrier.", how about other settings, for example, parity and stop bit, is it odd parity without stop bit? (...) (25 years ago, 7-Sep-01, to lugnet.robotics.rcx.nqc)
 
  Re: Code-only Line-tracking competition
 
Hi, (...) I would personally like to have an RCX with leJOS 1.0.2 at my disposal if I'm granted access to participate... How many participants can you handle? To me it seems like you could get thousands for the "code only" contest! Regards, Martin (...) (25 years ago, 7-Sep-01, to lugnet.robotics)
 
  Re: Code-only Line-tracking competition
 
(...) Good question. We DO have plenty o' RCX at our disposal. If you have specific firmware requirements, hook us up with them, and we will do our best to get one configured the way you want it. (25 years ago, 7-Sep-01, to lugnet.robotics)
 
  Re: Code-only Line-tracking competition
 
Hi there, (...) In the official rule page ((URL) it says: "Robots may be programmed with any software at your disposal" but that is hardly the case for the code only competition? though I couldn't find any explicit writing about the rules there... (...) (25 years ago, 7-Sep-01, to lugnet.robotics)
 
  Code-only Line-tracking competition
 
You can enter the WORKSHOP 3D LEGO RCX Challenge - a robot competition to be held in Seattle on October 6th - even if you don't want to travel here. There will be a "code only" line-tracking event that anyone can enter. Build a "standard robot" at (...) (25 years ago, 7-Sep-01, to lugnet.robotics, lugnet.robotics.rcx)
 
  Next Seattle robot competition - October 6th, 2001
 
It's been a bit less than a year since the last WORKSHOP 3D LEGO RCX Challenge in Seattle. This will be the third time the competition is held. It is scheduled for October 6th, 2001. There will be three main events: line-tracking, sumo, and (...) (25 years ago, 7-Sep-01, to lugnet.events, lugnet.robotics.events)
 
  RCX 3.0 and legOS 1.2.4
 
LEGO company will release RCX 3.0 at the end of next year, it will have 6 input port and 6 output port, 20x200 dots LCD, CPU is H8/3294 with 32K ROM and 64K RAM, it has a power socket as RCX 1.0, and with a built-in speaker, you can play wav or mid (...) (25 years ago, 7-Sep-01, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
 
  New patch for remote and message
 
I made a new patch for remote control and standard firmware message communication, I defined three config constants in config.h: 1. CONF_REMOTE_CTRL: Remote control services, comment it if you don't use remote control. 2. CONF_MESSAGE: Standard (...) (25 years ago, 7-Sep-01, to lugnet.robotics.rcx.legos)
 
  Re: powering RCX2.0
 
(...) However many people had problems when using DC power regularly - probably becuase it burned out one half of the rectifier. I'd advise using a 10V AC adapter if you're gonna be using it regularly. (Of course you've gotta get a RCX 1.0 first!!) (...) (25 years ago, 7-Sep-01, to lugnet.robotics)
 
  Re: powering RCX2.0
 
RCX 1.0 is the only unit that has a 9 volt adapter port. You can use an ac or dc 9volt supply on this. The power supply for the trains is suitable. -- Bob Fay rfay@we.mediaone.net The Shop (URL) Radu" <lego-robotics@crynwr.com> wrote in message (...) (25 years ago, 6-Sep-01, to lugnet.robotics)
 
  powering RCX2.0
 
Hello, I think I remember a post about using a 9V adaptor to power some version of the RCX during testing, but could not find it on the website. Do I remember this right? Thanks! -cmr (25 years ago, 6-Sep-01, to lugnet.robotics)
 
  torsen differential
 
i've got nothing but time lately so i'll get a *.dat of the differential made pretty soon, of course all credit goes to Brian Alano. i will set up the dat so the steps are from front to back like usual. should be done by the weekend. m. (25 years ago, 6-Sep-01, to lugnet.robotics)
 
  Re: Cybermaster alternative software
 
(...) You can use NQC which supports several targets (RCX, RCX2, Scout, and CyberMaster). Call Lego Consumer Affairs (search News, or check lego.com for the number), they may be able to replace your German CD with an english language version if you (...) (25 years ago, 6-Sep-01, to lugnet.robotics.cybermaster)
 
  Cybermaster alternative software
 
Hi, I just received a german Cybermaster kit and was wondering what the programming alternatives for it are. Can you use NQC and Java with the Cybermaster like the RCX, does anyone know? thanks, Mark. (25 years ago, 6-Sep-01, to lugnet.robotics.cybermaster)
 
  Re: Anyone know how to build a stall sensor?
 
(...) Yes. I just got a rotation sensor. Trouble is that the motors could stop for a variety of reasons (like the robot isn't moving). That isn't the real reason though (I could always handle that in software). The real reason is that ever since I (...) (25 years ago, 6-Sep-01, to lugnet.robotics.rcx)
 
  Re: Anyone know how to build a stall sensor?
 
(...) Yes. I found on article on using the battery voltage to determine the same thing, i.e. more current, less volts. To do it you need replacement firmware. I use leJOS (a Java VM), I'm one if the developers, so I could go in that way. I'm going (...) (25 years ago, 6-Sep-01, to lugnet.robotics.rcx)
 
  RTSJ
 
So you're in to Java and the RCX? If you're in to it deep then you might be interested in the Real Time Specification for Java (RTSJ) at: (URL) - Paul (25 years ago, 6-Sep-01, to lugnet.robotics.rcx.java)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR