 | | Re: Serial LED is not lighting up during charger board assembly
|
|
Hi Scott, as I mentioned before i only assembled some 6.270 boards, but no handyboard. So what's follwing is only what i guess. I can't check this out here. Are you able to measure (always with pin7 J9 as ground reference) +9V at pin2 U16 and -9V at (...) (25 years ago, 26-Aug-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: Question about necessary tools for HB assembly
|
|
Hi Scott, I assembled three 6.270 boards (kind of grandpa of handyboard) some month ago and didn't need an Oscilloscope or a Logic Probe. I guess you'll only need such things if you run into trouble with getting started with your handyboard. So, try (...) (25 years ago, 26-Aug-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: Building a peripheral bus from motor output
|
|
(...) Id be surprised if you could pull 300baud, much less 2400, even assuming perfect patterns. But for low speed comm, it'd work... though I doubt any better than the infrared port! (25 years ago, 26-Aug-01, to lugnet.robotics)
|
| |
 | | EmuLegOS support for windows
|
|
The subject pretty much says it all. You'll need cygwin, and then it works. There is now LNP support for EmuLegOS on windows now due to the differences in the WinLNP API and the RCX LNP API. mark (25 years ago, 26-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Wireless IR transmission
|
|
I am trying to make a computer controlled robot, but I don't want it to be tethered. The only way I have thought of to do this would be to put the IR tower on the bot itself and get some kind of wireless transmitter for it. Does anyone know where I (...) (25 years ago, 24-Aug-01, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 Arrays
|
|
(...) Fixing that has been on the to-do list for a long time. But it just isn't a high priority since there are easy workarounds. Right now adding USB support is top priority. Dave Baum (25 years ago, 26-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: tweaking around dlcd_show( )
|
|
(...) Ooops! I obviously wasn't looking at it properly last night (only browsing through the zip file). As 'dlcd_show' is defined as a macro that takes one parameter, but uses it twice to each of BIT_OF and BYTE_OF, which in turn both take 2 (...) (25 years ago, 26-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Love the new Music capability with the new firmware!
|
|
(...) If you're using NQC and tell the compiler you're targeting RCX 2.0 (-Trcx2 for the command line version), then PlayTone() will accept a variable frequency. Duration, however, must still be constant. Dave Baum (25 years ago, 26-Aug-01, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 Arrays
|
|
(...) Manual? Manual! We don't need no stinking manual. Thanks, ("I guess I should read it", he says sheepishly) (25 years ago, 26-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Building a peripheral bus from motor output
|
|
Hi all, I recently read an excellent paper by Fred Martin (of MIT fame) on building toys in a modular fashion. His microcontroller was similar to the RCX but had one key addition - a two wire serial bus so that active peripherals could be attached (...) (25 years ago, 25-Aug-01, to lugnet.robotics)
|