 | | RE: Love the new Music capability with the new firmware!
|
|
(...) That IS cool. Now the problem is to figure out if this new feature was implemented using the exisiting ROM or if the entry points have changed. Has anybody tried to run legOS or pbForth on the new RCX 2.0? (Maybe I can use this as an excuse to (...) (25 years ago, 24-Aug-01, to lugnet.robotics, lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
 | | Love the new Music capability with the new firmware!
|
|
I don't know if people have discussed this already or not, but I'm just playing around with the new firmware now and I can finally do what I have wanted to do for 3 years, and that is to make the frequency played by the RCX be a function of a (...) (25 years ago, 24-Aug-01, to lugnet.robotics)
|
| |
 | | Need help with RcxCC: I get "The system cannon find the file specified" error.
|
|
Hi. I'm having problems with RcxCC. I hope you can help me. I've just installed RcxCC v. 3.2. I use Win2000 and RIS 1.5. When I compile a simple program, I get following error message: " Win32 Error. Code: 2. The system cannot find the file (...) (25 years ago, 24-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Power inlet to RCX 1.5?
|
|
(...) I'd use a 9V 1.5A _regulated_ power supply. Lower ampere ratings should also work until you stall three motors ... Jürgen (25 years ago, 24-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Power inlet to RCX 1.5?
|
|
(...) Yes, but there are only pictures, no circuit diagram. It is very hard to figure out a circuit from photos, it is much easier if you really have the thing. Jürgen (25 years ago, 24-Aug-01, to lugnet.robotics)
|
| |
 | | Re: bushing (bush) question
|
|
In lugnet.robotics, Bram Lambrecht writes: [...] (...) I think this is correct. I once built the "Aliens" type walker, (URL) . I used Type 2 originally and found that after the thing would walk a few meters one of the legs would pop off. Didn't have (...) (25 years ago, 24-Aug-01, to lugnet.robotics, lugnet.technic)
|
| |
 | | Re: Lego Dacta Control Lab software
|
|
Looks like only PC is available on that site. Could you give me a site for the Mac version? Thanks for your time, (...) (25 years ago, 24-Aug-01, to lugnet.robotics)
|
| |
 | | RE: bushing (bush) question
|
|
(...) Type 2 is newer, probably because the Type 1's were too hard to take off the axle. I've noticed that most of my loose Type 1's have a hairline fracture on one side. (...) All the parts with teeth were essentially replaced with functional (...) (25 years ago, 24-Aug-01, to lugnet.robotics, lugnet.technic)
|
| |
 | | Re: How to communication between RCXs without PC?
|
|
You know I had finished my control program in NQC, it is not so simple, but I need to control LEGO Train in smooth speed, NQC is limitation, so I want to use legOS for one of RCX, could you give me some hints for sending/receiving NQC style message (...) (25 years ago, 24-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: How to communication between RCXs without PC?
|
|
(...) As far as I know, it is not possible to communicate between legOS and NQC using LNP. I think it would be possible to directly drive the IR port from your own code to send and recieve NQC-style communications, but the ability isn't built into (...) (25 years ago, 24-Aug-01, to lugnet.robotics.rcx.legos)
|