To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *29544 (-10)
  Re: Proper power supply for a 1.0?
 
(...) I've used the Train Transformers with great success. If you look close at your RCX you'll notice 9-12~ Anything from 9 to 12 volts AC or DC will work fine. Though to prevent your RCX's Diode Bridge from burning out AC is better. (Shares the (...) (25 years ago, 23-Aug-01, to lugnet.robotics.rcx)
 
  Migrating from IR tower/spirit.ocx to USB
 
Now that I have a 2.0 kit and have had some time to realize that the new USB tower uses a proprietary protocol I can see that rescuing all the code I’ve been writing in Visual Basic will be tougher than just redirecting the IO to a USB masquerading (...) (25 years ago, 23-Aug-01, to lugnet.robotics)
 
  Re: Proper power supply for a 1.0?
 
(...) Well on the back of the LEGO train power supply it list Output as 12VAC 7VA, so I'm assuming that the DC conversion is done in the speed regulator, I couldn't tell you why. But it's good to know I can use this power supply with a 1.0 RCX since (...) (25 years ago, 23-Aug-01, to lugnet.robotics.rcx)
 
  Re: Be VERY careful with that train transformer (was:Proper power supply for a 1.0?)
 
(...) heh, notice that the original question was about the "power supply that goes with the 0v train spee dregulator" - so we're talking about lego transformers, not just any train transformer. :) (25 years ago, 23-Aug-01, to lugnet.robotics.rcx)
 
  RE: What's the difference between RIS 1.5 and 2.0?
 
Most of the questions have already been answered. Go to the website, and search backwards for "RIS 2.0". Tilman (...) (25 years ago, 20-Aug-01, to lugnet.robotics)
 
  Re: Help neeeded in S19
 
Hi Chee, I used the assembler code of this shaft encoder software to create my own. Although using them in C is quite simple, programming in assembler much toucher - but very nice. Take a look at my website (URL) for the altered shaft encoder code. (...) (25 years ago, 23-Aug-01, to lugnet.robotics.handyboard)
 
  Re: Proper power supply for a 1.0?
 
(...) true - but I think the RCX input is rated 9-12V. I don't have a train transformer here, but wouldn't it be outputing 12VDC? Can't imagine why they'd put a AC to DC converter in the regulator... Anyway, we've used the train transformers many (...) (25 years ago, 23-Aug-01, to lugnet.robotics.rcx)
 
  Proper power supply for a 1.0?
 
What is the proper voltage for a external power supply for a 1.0 RCX? Can I use the power supply that goes with the 9v train speed regulator? I believe the train transformer outputs 12VAC. jt (25 years ago, 23-Aug-01, to lugnet.robotics.rcx)
 
  where to look for in the legos source? gcc2.95.2 and win200?
 
I found in the linux pcmcia forum, that the serial pcmcia card from Socket Communications, which I want to use to download programs to rcx, sets the speed internally four times faster then expected. Is there a possibility in the firmdl3 and (...) (25 years ago, 23-Aug-01, to lugnet.robotics.rcx.legos)
 
  Re: problems with legos on notebook
 
Hallo Ross! I found in the linux pcmcia forum, that the socket pcmcia card, which I am using, sets the speed internally four times faster then expected. Is there a possibility in the firmdl3 and dll-source to divide the speed for the serial port by (...) (25 years ago, 23-Aug-01, to lugnet.robotics.rcx.legos)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR