To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *29469 (-20)
  Re: ir communication
 
(...) Chris (25 years ago, 14-Aug-01, to lugnet.robotics.rcx.legos)
 
  Re: Is Expansion Board Servo Voltage Suppose to Be 9v
 
Make sure you measure the voltage under load. Without a load the diodes won't look like they're dropping anything. Fred (...) (25 years ago, 15-Aug-01, to lugnet.robotics.handyboard)
 
  Re: Is Expansion Board Servo Voltage Suppose to Be 9v
 
Yes, Fred, the diodes are in place. I Assume that is where I should start to test for opens, shorts and, bad diodes. Thanks for the help. Andy "Fred G. Martin" <fredm@alum.mit.edu> wrote in message news:200108150241.WA...net.com... (...) (25 years ago, 15-Aug-01, to lugnet.robotics.handyboard)
 
  Re: WinVLL released
 
I received the Italian version Winvll.ini from Stefano Maffulli. Thank you, Stefano. I append it to the archive. And I wrote how to make VLL Probe page today. You can use the Winvll without USB Tower (RIS2.0). Please visit again my page. Now there (...) (25 years ago, 15-Aug-01, to lugnet.robotics, lugnet.robotics.edu, lugnet.robotics.microscout, lugnet.robotics.vll)
 
  updates to my site
 
Hi everyone, Just letting you know that I have recently updated my site. For those who haven't seen my site before, some of the highlights are: a Window walker, a photocopier, a Logo type Turtle, some gear boxes, etc. Building instructions for some (...) (25 years ago, 15-Aug-01, to lugnet.robotics)
 
  Re: Is Expansion Board Servo Voltage Suppose to Be 9v
 
Do you have the dropping 2n540x diodes in place? they should drop the 9.6v batt to the 5-6v servo voltage. Fred (...) (25 years ago, 15-Aug-01, to lugnet.robotics.handyboard)
 
  Is Expansion Board Servo Voltage Suppose to Be 9v
 
Hello again, I was surprised to find that my expansion board servo ports were putting 9 volts. Is this the way the board was designed or is this in error. Most servos I have come across work in the upper 4 to 6 volt range. The servo I have runs (...) (25 years ago, 15-Aug-01, to lugnet.robotics.handyboard)
 
  Help Needed With Serial Output Drivers Syntax
 
Does anyone have an example of how to use the 7i9600 serial driver with the Scott Edwards SSC II. I cannot seem to find any documentation. Thanks, Andy Loy andyl@citlink.net (25 years ago, 14-Aug-01, to lugnet.robotics.handyboard)
 
  Dos VLL Interpreter / Driver
 
Hi all; I have developed a DOS VLL Interpreter / Driver that does not use the Scout to talk to the MicroScout, rather it uses a simple LED driver circuit direct attached to the PC Parallel port. There are two versions; both DOS based. One is a (...) (25 years ago, 14-Aug-01, to lugnet.robotics.vll)
 
  Report from RoboCup 2001
 
RoboCup 2001 Seattle, WA August 2-10 2001 Same story, multiple URLs: (URL) site: (URL) (25 years ago, 14-Aug-01, to lugnet.mediawatch, lugnet.robotics.events)  
 
  Re: transfer data failed
 
yes I did ... :-( manuel (...) (25 years ago, 14-Aug-01, to lugnet.robotics.rcx.legos)
 
  Re: Problem in Battery Power
 
Hi Chee, I have been told the power still needs to be supplied from that connector. My idea was to only use two of the four connecting pins (one for plus and one for minus) downward from the expansion board and solder two female connectors (one for (...) (25 years ago, 14-Aug-01, to lugnet.robotics.handyboard)
 
  not strictly legOS
 
hi all, im doing a research project over here and in the process i have set up lnpd and now have continous communication between my robot and the PC. Now then here is the deal, there is a teoretical posibility that i will get more inputs from my (...) (25 years ago, 14-Aug-01, to lugnet.robotics.rcx.legos)
 
  Problem in Battery Power
 
Hi ! I am a research student in Robotic. I am using Handy Board together with Expansion Board to interface with DC motors and other sensory devices. Unfortunately, internal power supply is not adequate for powering my motors. So, I am thinking to (...) (25 years ago, 14-Aug-01, to lugnet.robotics.handyboard)
 
  Re: WinVLL released
 
Rainer Balzerowski sends me German version ini file. I am very happy. I append it to the archive. I am looking forward to receive other languages ini files. Thank you. (URL) (25 years ago, 14-Aug-01, to lugnet.robotics, lugnet.robotics.edu, lugnet.robotics.microscout, lugnet.robotics.vll)
 
  Re: (MS)2 Expander Web Site Updated
 
Elegant! (...) (25 years ago, 14-Aug-01, to lugnet.robotics)
 
  Re: WINLNP QUESTIONS
 
I did some more digging. When I look into the reg I do not find the reg keys as mentioned on the (URL) page. I dig in the code and set the com port by hand (directly to com1) and now I have the green ligth on the IR tower. However still no messages (...) (25 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
 
  (MS)2 Expander Web Site Updated
 
I've updated my website with some changes to the building instructions for the (MS)2 Expander that might make it easier to build. (URL) Husby LUGNET Member #320 TFM's LEGO Workshop - www.akasa.bc.ca/tfm The Vancouver LEGO Club - www.akasa.bc.ca/vlc/ (25 years ago, 13-Aug-01, to lugnet.robotics, lugnet.robotics.rcx)
 
  Re: ir communication
 
Yes there is. It is LNP it is availiable for windows or linux. I am just fiddling with the windows version see: (URL) I did not get it working just fine see also my post just before you (...) (25 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
 
  ir communication
 
Hi, i am just doing my first steps with legOS and i want to send some data back to the PC. Is there any kind of software for the PC to read that data and save or display it? TIA Chris (25 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR