 | | Display the value of Scout sensors
|
|
Scout is cheaper, but when you debug NQC program in Scout, you have no way to watch the value of its sensors, I made a small program that can show sensors value in a RCX LCD, you can use remote to change watching sensor, message 1 for sensor1, (...) (25 years ago, 26-Jul-01, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
 | | Re: Got my RIS 2.0 set
|
|
(...) [snip] (...) Hi Tilman, thanks a lot for the info. I personally don't use RCX Code to write my programs, but IMO the addition of variables and instructions to manipulate them is the most important change. This makes the software much more (...) (25 years ago, 26-Jul-01, to lugnet.robotics)
|
| |
 | | RE: To whoever has RIS 2.0...
|
|
There's no part number on it. The cable is permanently attached to it. The new tower is a very different beast than the old one. It does not show up as a serial port on your system. I'm pretty sure you will need the 2.0 software to use it. That's (...) (25 years ago, 26-Jul-01, to lugnet.robotics)
|
| |
 | | RE: Got my RIS 2.0 set
|
|
(...) I was talking about the new USB tower, not the RCX. The RCX is visually unchanged, except for the "2.0" inscription on the side. Tilman (25 years ago, 25-Jul-01, to lugnet.robotics)
|
| |
 | | RE: Got my RIS 2.0 set
|
|
(...) Doesn't that mean the ROM must have been changed? IIRC the RCX 1.0 could not do VLL... Chris (25 years ago, 25-Jul-01, to lugnet.robotics)
|
| |
 | | Makefile Design - Observation, and Query to Paolo Masetti
|
|
The latest CVS version of legOS adds explicit detection of CygWin 1.1 (and by extension 1.3) This did, however work anyway, with Cygwin 1.1 being detected alongside the older cygwins, due to a quirk in make's findstring - specifically, that: (...) (25 years ago, 25-Jul-01, to lugnet.robotics.rcx.legos)
|
| |
 | | smart remote programs for windows?
|
|
I saw some programs for a palm pilot that makes it a learning remote. They were used in the same way the Lego remote was: directly controlling the rcx. I was wondering if anyone had a link for the same thing for a pc/laptop... -Rob (25 years ago, 25-Jul-01, to lugnet.robotics.rcx)
|
| |
 | | Re: Any success running IC with W2000 on notebook?
|
|
Hi Steve, I have been running IC version 3.2 without any problems on W2k. Not on a notebook though. You can obtain a personal version of IC 3.2 from NetwtonLabs (www.newtonlabs.com/ic) for $35. Good luck, Willem van Asperen "Steve Mosiman" (...) (25 years ago, 25-Jul-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: Fame for your RCX 1.5
|
|
(...) Clearly, the CAD part should ALWAYS be the one with the power adapter port because it will allow builders to see graphically whether there is enough clearance to plug an AC adaptor into their creations. (It would be cool to model a variety of (...) (25 years ago, 25-Jul-01, to lugnet.robotics)
|
| |
 | | To whoever has RIS 2.0...
|
|
What is the part number for the IR tower and cable? I'm going to try to finagle(sp?) my way into one. Or...tell me the difference in the internals of the new usb tower and the old serial tower. I might could install a new cable and upgrade my (...) (25 years ago, 25-Jul-01, to lugnet.robotics)
|