 | | Re: lnp rcx hostaddress [and a summer legOS release?]
|
|
Hi I'm preparing for the same project Vittorio's working on, a high level library in C++ to send explicit commands to rcx from a pc and back. I hope if you gonna change the low level library you will mantain a certain compatibility so that I won't (...) (25 years ago, 28-May-01, to lugnet.robotics.rcx.legos)
|
| |
 | | download .s19 problem
|
|
Hy! I have problems downloading a self compiled file to my Handyboard (with 68HC11A1). I just wrote a little test programm: int main() { int foo = 0; while (foo < 1000) { foo++; } return(0); } and compiled it to a .s19 file with the gnu gcc 68hc11 (...) (25 years ago, 28-May-01, to lugnet.robotics.handyboard)
|
| |
 | | RE: Custom Firmware, IR Problems, and Dead RCXs
|
|
Ralph, Thank you for painting a much clearer picture of the internal design of the IR Tower. I agree with your observations, but have a question: Is the processor in the IR Tower controllable (i.e. downloadable, like the RCX)? If it is, then there's (...) (25 years ago, 28-May-01, to lugnet.robotics)
|
| |
 | | RE: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
(...) You are right, but the RCX and the tower are right at the hairy edge. The additional 50R impedance will leave the near mode essentially unchanged and I'll sacrifice on the high range. Start with the tower. If you use a 9V battery, the IR (...) (25 years ago, 28-May-01, to lugnet.robotics)
|
| |
 | | Re: Where Can I gat the file Spirit.ocx?
|
|
It's on your Mindstorms CD. Just do a search and you'll find it : ) It should have already been installed on your machine as well. It'll show up in the components list under the project menu in VB as the "LEGO PBrickControl, OLE Control module." (...) (25 years ago, 28-May-01, to lugnet.robotics)
|
| |
 | | RE: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
Hi all, Just a couple a quick comments on this thread - I'm a firmware design engineer who's done lots of work with IrDA. I don't, however, have any experience with the internals of the RCX or the IR Tower, other than owning them and reading this (...) (25 years ago, 27-May-01, to lugnet.robotics)
|
| |
 | | Where Can I gat the file Spirit.ocx?
|
|
Hello All, I'm a newbie at Mindstorm programming, but I saw on the internet that We can use the spirit control on VB programs to control the rcx. Where can I find it? Thanks (25 years ago, 27-May-01, to lugnet.robotics)
|
| |
 | | Re: RCX motor pulsing
|
|
I have been using RCXs to control tracks, you also can control signal in the (...) (25 years ago, 28-May-01, to lugnet.trains, lugnet.robotics)
|
| |
 | | IR Tower 'On' with WIN98
|
|
Picking up a thread a few weeks old, I just moved into a new 'box' running Win98. The IR Tower light stays on all the time. One previous note suggested: change the battery; that did nothing. I will probably try the other serial port. If anyone has (...) (25 years ago, 27-May-01, to lugnet.robotics)
|
| |
 | | RE: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
(...) Well, yes and no. The biggest risk is when you use the tower or the RCX in high-power (far) mode for extended transmissions. I was thinking about why we have not received more posts about dead RCXs. My old pbForths (and I think legOS too) set (...) (25 years ago, 27-May-01, to lugnet.robotics)
|