 | | Re: RCX motor pulsing
|
|
I have controlled LEGO trains via the RCX many times. The question is how to control the speed of the train under a finer ganularity then just the native power levels. snip ...this comment has promise! Can you vary the width of the pulse? <The good (...) (25 years ago, 22-May-01, to lugnet.trains, lugnet.robotics)
|
| |
 | | Re: Wishlist leJOS
|
|
(...) I think that the datalogging area is just a special limited firmware array, but , IIRC, since it mentions nowhere that you have to remember to keep the datalog size into account. Try using the opcodes, and see what works. Andy -- See my Visual (...) (25 years ago, 21-May-01, to lugnet.robotics.rcx.java)
|
| |
 | | Re: High Strength Powered Steerable pivot wheel
|
|
(...) Well I feel a total fool, sorry Steven. (Embarrassment tempered by the fact that you can still get them.) (...) Here's the original post about this... (URL) (must remember to switch brain on while at work in future) (25 years ago, 21-May-01, to lugnet.robotics)
|
| |
 | | SHRIMP building was: Re: High Strength Powered Steerable pivot wheel
|
|
(...) In the near term, I've opted out of the "steer in place" requirement. That way I go from four outputs to two. With an 8-wheel SHRIMP, I steer like a four-wheel steered (FWS) car does at low speed. Also, I don't have to worry about the friction (...) (25 years ago, 21-May-01, to lugnet.robotics)
|
| |
 | | Re: Wishlist leJOS
|
|
(...) It does answer my question, but I was thinking that a feature like that would be more memory efficient. It seems to me (knowing very little of programmimg small devices) that there are special OP codes (looking at Keokea Proudfoot's RCX (...) (25 years ago, 21-May-01, to lugnet.robotics.rcx.java)
|
| |
 | | Re: High Strength Powered Steerable pivot wheel
|
|
The problem appears to be leverage. I have no exposed shaft at all. But the force while climbing stairs still managed to snap the axle at the pivot point. I was suprised the axle broke and the retainers did not just pop off. A steerable shrimp is a (...) (25 years ago, 21-May-01, to lugnet.robotics)
|
| |
 | | Re: Hardware Hacking the MicroScout
|
|
(...) No problem... If you know of anyone that can program in PocketPC let me know... I'm trying to get NQC ported to an ARM version of PocketPC. Dean (...) -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 21-May-01, to lugnet.robotics.microscout)
|
| |
 | | cvs changes
|
|
Hi, I checked into the CVS repository some changes today. They include: A) a fix to util/dll-src/Makefile to reference ../../kernel/lnp.c, so a symbolic link or copy is not required. B) small changes to various makefiles to get c++ support working (...) (25 years ago, 21-May-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: c++
|
|
Hi, Sorry that I've been AWOL! Attached is a set of patches you can apply to the 2.5 distribution to clean up most of the make process. You will still have to correctly specify the TOOLPREFIX in Makefile.common, or via the make command line. You can (...) (25 years ago, 21-May-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: High Strength Powered Steerable pivot wheel
|
|
(...) I think that no current set includes them. But it's available as spare part in the Pitsco/DACTAcatalog (US only). (...) This is actually the same solution I was thinking to implement: steerable front and rear wheels and side wheels driven like (...) (25 years ago, 21-May-01, to lugnet.robotics)
|