To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *27614 (-10)
  Unsubscribe
 
Sorry, I knew I shouldn't post this but I can not unsubscribe to this newsgroup. I have tried to stop this by going through the option and it doens't recognize this subscription. Please take t-f-l-y@home.com out of you system. Thanks (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
(...) You can find light sensor schematics on Michael Gasperi's page: (URL) Using the RCX IR emitter as the illumination source. Don't know (...) Someone has already tried this. You can check Simen Svale Skogsrud's page for an example, with NQC (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Assembly in my C-program
 
(...) If you want to drive directly the motors you should first disable motor handling in legOS (remove CONF_DMOTOR definition in config.h). Then you can create a high priority task that switches motors on and off writing in the motor output port. (...) (26 years ago, 28-Mar-01, to lugnet.robotics.rcx.legos)
 
  Re: Assembly in my C-program
 
(...) pulses (...) at (...) would (...) Hmmmm. This should be possible, but it's a bit more tricky with stepper motors - you have to allow for the speed-up and slow-down. Thus just calling motor_speed(50) would have to initiate a task that starts (...) (26 years ago, 28-Mar-01, to lugnet.robotics.rcx.legos)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
Ralph Hempel had an example of the heat-shrink tubing solution here: (URL) also tried used some black vinyl from a binder? -Tim (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
To make a passive light sensor, you can use a design like Michael Gasperi's: (URL) costs only a couple bucks, and works quite well. If you would like better response from your lego light sensor, you can use a piece of black shrinkwrap tubing and (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
Hi Chris, You can turn off the LED with software though you may be a little disappointed with the light sensitivity. The reason the LED is on is because your program has set the sensor to an active sensor. If you set the type to NONE make the mode (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
(...) Maybe. I think RCX2 with NQC has some crude arrays, I haven't looked into them yet, but I might be able to use them to do simple mapping on the RCX. Or something even cruder if I don't have arrays. (...) Ahh. Hmm. I wonder what it actually (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
This sounds very cool. If you want to do the mapping at the bottom, you will have to use alternitive firmware anyway (right?), and they have a passivate command that turns off the light. It passivates the sensor, but I don't think standard firmware (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Shutting off illumination LED on Light Sensor for LIDAR
 
Has anyone successfully found a way (short of paint, or cutting internal wiring) of shutting off the red 'supply light' LED on the Lego light sensor? The supply LED is great for active-detection situations, like line-following, when you need to (...) (26 years ago, 28-Mar-01, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR