 | | Play pcm on the RCX
|
|
I think this item has been discused sometimes but I have discovered RIS, just last Christmas. Has anyone played a pcm wave? I know how to play it on a PC speaker, but I don´t know a lot on H8 architecture and so on the timers (26 years ago, 2-Feb-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Is an RCX Output Amplfier, possible ?
|
|
(...) Actually, you need four transistors in what is called an H-bridge configuration. This is due to the fact that the motors are usually intended for bi-directional use. If you are only using them in one direction, a single transitor will suffice. (...) (26 years ago, 12-Feb-01, to lugnet.robotics)
|
| |
 | | POPTRONICS isn't worth it
|
|
For those of you who have seen the March 2001 issue of Poptronics (the "Special Robotics Issue") and been attracted by the words "Lego Mindstorms" in bold type one the cover - believe me, it isn't worth it. In the finest traditions of Popular (...) (26 years ago, 12-Feb-01, to lugnet.robotics)
|
| |
 | | Re: Underwater Sensors
|
|
(...) First off, beware that ordinary tap water contains dissolved impurities and is electrically conductive. (Water itself, BTW, is actually an insulator - it's the dissolved impurities that give it conductivity). It usually isn't an issue with (...) (26 years ago, 12-Feb-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: Walkers
|
|
Thanks for the feedback people. I asked the question because I have been working on a walker for around 6 weeks, and was getting a bit discouraged. I have since had some success on the weekend. My walker will now go through it's complete walking (...) (26 years ago, 12-Feb-01, to lugnet.robotics)
|
| |
 | | Re: legOS
|
|
(...) "could not open serial port" generally means one of these things: 1) You told NQC to use a serial port that doesn't exist. By default, it will try to use Mac - modem port Win - COM1 Unix - /dev/ttyS0 You can override this with a -S option. 2) (...) (26 years ago, 12-Feb-01, to lugnet.robotics.scout)
|
| |
 | | Check out this site!
|
|
Terry Gathright came across this great site and thought you might want to check it out. We hope you enjoy it! (URL) Gathright wrote: Hi Guys, Check this location for some hi power motor drivers, I have ordered two of the 35 amp boards and will let (...) (26 years ago, 12-Feb-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: downloading pcode
|
|
Make sure that your phone wire between the HB and interface board has four wires, most generic phone wires only have two wires in them. -Dan (...) and (...) MAX232 (...) I (...) any (...) (26 years ago, 12-Feb-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: Underwater Sensors
|
|
James, maybe a moisture sensor out of a VCR could be modified to meet your needs??? They are made to detect condensation in VCR's. but if all else fails... water is a conductor, so you could theoreticly just put two bare contacts on the outer part (...) (26 years ago, 12-Feb-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: Short Circute Problem -- EMERGENCY
|
|
Raju, I have a handyboard version 1.21, on this board the battery led is working properly when it lights at power on and then goes off. According to the manual it should only remain lit when the power is too low indicating a dead battery. So I (...) (26 years ago, 12-Feb-01, to lugnet.robotics.handyboard)
|