 | | Re: Visual NQC 2001
|
|
<Runtime error 380 fix If you get Runtime error 380 during compile start you need to change the subdirectory where NQC.exe is stored. Use a directory without a space in the name. Example C:\NQC\nqc.exe This will work.> That did not work. I am still (...) (26 years ago, 1-Feb-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Anyone using Mac beige G3
|
|
(...) One thing to keep in mind about Mac serial ports is that they are not RS-232, rather they are RS-422. IIRC, RS-232 is a singled-ended voltage standard (ref to ground only), where RS-422 is a differential standard. The 'common' method of using (...) (26 years ago, 1-Feb-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Pneumatic tubing...
|
|
(...) I suppose you could check medical supply shops... You could also try www.newark.com, and request a catalog. If you are using Netscape Communicator, just type "pneumatic tubing" (without the quotes) into the URL field, and start with those (...) (26 years ago, 1-Feb-01, to lugnet.robotics)
|
| |
 | | RE: 68HC11 (Evaluation Board)
|
|
I was wondering if anyone was aware of any pre-existing library calls that would allow an individual using an Evaluation Board (EVB-68HC11)+ Buffallo Monitor(ImageCraft C v5.0) to access the system clock. I've noticed that with using Interactive C (...) (26 years ago, 1-Feb-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: Pneumatic tubing...
|
|
Dear Tom (...) Thanks for your reply. You'll notice that I mentioned in my original question that the tubing available in the RC shops (which I referred to as poly tubing rather than neoprene -- my bad) is a bit stiff. I had a vague memory of (...) (26 years ago, 1-Feb-01, to lugnet.robotics)
|
| |
 | | Re: Anyone using Mac beige G3
|
|
(...) I've had similar problems with a CyberMaster. It seems that CyberMaster Tower is powered by the serial interface (at least it is switched on by this power). On PC, the DTR line is switched high (12 V), and the CTS line is switched low (-12V). (...) (26 years ago, 1-Feb-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Pneumatic tubing...
|
|
(...) can't (...) (vacuum (...) be (...) I don't know, I found the following on the first page of search results for "pneumatic tubing", took all of 3 seconds: (URL) (26 years ago, 1-Feb-01, to lugnet.robotics)
|
| |
 | | Pneumatic tubing...
|
|
I know I've seen someone suggest a non-LEGO source for tubing compatible with LEGO pneumatics, but after half and hour of searching through past posts I can't locate it (so sorry for any repitition). I have tried auto parts stores (vacuum tubing -- (...) (26 years ago, 1-Feb-01, to lugnet.robotics)
|
| |
 | | Re: Can I use two cybermasters
|
|
Without picking up the soldering iron and modifying its frequency, talking to multiple CyberMasters on the same frequency is, I guess, very similar to talking to multiple RCXs through IR. When the PC sends out a command through the tower, every (...) (26 years ago, 1-Feb-01, to lugnet.robotics.cybermaster)
|
| |
 | | unsuscribe
|
|
How do i unsuscribe from the list? Thank you. (26 years ago, 1-Feb-01, to lugnet.robotics.handyboard)
|