 | | Re: IR Tower problems
|
|
(...) Don't try this at home kids !!!...!!! NO ! This can't work !! The printerport is as parallel port and not a serial port. The availablity of the IR-tower is checked by using the serial handshake line. This can't work with printerport ! (...) I (...) (26 years ago, 22-Jan-01, to lugnet.robotics)
|
| |
 | | Re: Interfacing Sharp's GP2D02 Distance Sensor to the RCX
|
|
(...) I agree ! (...) How depressing. :-( (...) Of course ! But, it's possible to drive more then one of these sharps with one output. And shouldn't it be possible (without large effort) to use the input-power to multiplex some of the GP2D12 ? (...) (26 years ago, 22-Jan-01, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
 | | Re: Interfacing Sharp's GP2D02 Distance Sensor to the RCX
|
|
Ralf Krause <lego-robotics@crynwr.com> wrote in message news:B691251F.ED3%no...@web.de... Michael, please tell me how you can write that the power can " ... provide 30 mA of power to operate other sensor electronics." As I 've tested it seems that (...) (26 years ago, 22-Jan-01, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
 | | Reading PWM Servo Signal into Handyboard
|
|
I need to read the pulse width modulated signal put out by a radio control receiver into the Handyboard. I have thought about using a radio control PWM to electric motor speed controller and feeding this into an analog in port on the Handyboard but (...) (26 years ago, 22-Jan-01, to lugnet.robotics.handyboard)
|
| |
 | | Cybermaster: Cannot receive though sending works (w/o sprit.ocx)
|
|
Hi, I've written a small Visual Basic program so I can use Cybermaster under Windows 3.1x. (So I cannot use spirit.ocx.) Sending commands works (motor on/off, sound, etc.). But I don't get any echo. I cannot get any sensor data, and I can't see if (...) (26 years ago, 22-Jan-01, to lugnet.robotics, lugnet.robotics.cybermaster, lugnet.robotics.rcx)
|
| |
 | | Re: IR Tower problems
|
|
(...) I think it could probably work with the printr port. But what I would do is get a serial to printer port adapter or buy another wire which ever is cheapest. I have a wire that runs out the serial port with a 25 pin(i think) connection then an (...) (26 years ago, 21-Jan-01, to lugnet.robotics)
|
| |
 | | Re: Interfacing Sharp's GP2D02 Distance Sensor to the RCX
|
|
Hi, I asked this problem a few weeks (or months??? ... I don't know a what time ...) but nobody could help. I got the same following answer ".... the sensor takes 35 mA and this is to much for the RCX ..." but I couldn't understand this at this (...) (26 years ago, 21-Jan-01, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
 | | Re: programming interface i think
|
|
Don't shoot me if i'm wrong, but this site seems to be mainly about heat and energy. There is a link about using the RCX with Borland C++. When you download the file, you get the information on how to do this (in english) frank "not much left to (...) (26 years ago, 21-Jan-01, to lugnet.robotics)
|
| |
 | | RE: Anyone made animatronics with the RCX yet?
|
|
(...) I know this only works with pbForth, and it's not ALL Technic, but you can drive standard servos with the RCX. Here's how: (URL) You can even drive pneumatic switches with the servos... Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH (...) (26 years ago, 21-Jan-01, to lugnet.robotics.rcx)
|
| |
 | | Re: IR Tower problems
|
|
(...) Hi Greg, I'm not sure if the RCX IR Tower is the same than the Scout Tower, but I guess it's so. You can't use the printer port (LPT) for the tower. You have to use a serial port (COM1, COM2, ..). If you're not sure if you've got the right (...) (26 years ago, 21-Jan-01, to lugnet.robotics)
|