 | | Re: Limit Switches without using sensor inputs
|
|
Very sharp! A very clever and elegant solution to a common problem. (26 years ago, 15-Jan-01, to lugnet.robotics)
|
| |
 | | Re: Visual NQC 2001
|
|
(...) I've had similar results. I sent 5 or 6 bug reports to the author, but I suspect he may be a bit overwhelmed at the moment. I haven't heard a peep from him. (: Corey Snipes Boulder, CO, USA csnipes at qwest dot net (26 years ago, 15-Jan-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Motor mis-match.
|
|
Thank you! I'm glad to see someone has taken a semi-scientific approach to the whole question. I have one correction/comment to make though: It's doubtful that the Lego motors will heat up significantly enough to affect their operating speed. There (...) (26 years ago, 15-Jan-01, to lugnet.robotics)
|
| |
 | | Motor mis-match.
|
|
I was having a boring evening - so I decided to test some theories about Lego motors - and at the risk of seeming pedantic - here are my findings: Several times, people on this list have asked why their robots don't drive in a straight line - the (...) (26 years ago, 15-Jan-01, to lugnet.robotics)
|
| |
 | | Re: Redhat 7 and legOS
|
|
Just following up my own message. I have just tried the instructions with kgcc in redhat 7. It fails with exactly the same problem. All binutils and egcs compiled normally with kgcc except for the one error specified in the HOWTO. Mike Ruelle (...) (26 years ago, 15-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Dallas 1 Wire Interface on handyboard
|
|
Hi, has anyone implemeted Dallas Seminconductor 1Wire network on Handyboard? If not I'll take a a stab at writing the code, it doesn't look to bad according to the application notes. I've got several of the Dallas 1 wire thremometer chips.. pretty (...) (26 years ago, 14-Jan-01, to lugnet.robotics.handyboard)
|
| |
 | | Redhat 7 and legOS
|
|
I have gone through the HowTo setup legOS. The only problem I have had is that none of the demo code projects can compile. They all fail with [demo]# make /usr/local/crossgcc/...hi-hms-gcc -O2 -fno-builtin -fomit-frame-pointer -Wall (...) (26 years ago, 14-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: I ordered a 1.5 and was sent a 1.0 Good or Bad?
|
|
(...) Head to www.lego.com and search for Consumer Affairs in the search box in the upper right corner of the page. Click on "Help" in the results page. Search for the text "Consumer Affairs" in the page. There, you'll see a US Toll Free number, (...) (26 years ago, 14-Jan-01, to lugnet.robotics)
|
| |
 | | Re: 2 RealTimeJava for the 68HC11 Questions
|
|
(...) Other than seeing people write about it, I'm not familliar with this product. When you say "newly constructed" is that to say it's in a kit form? Who makes it and where do you get it? I understand that it's a microcontroller development board, (...) (26 years ago, 14-Jan-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: I ordered a 1.5 and was sent a 1.0 Good or Bad?
|
|
(...) I have exactly the same problem. How do you contact Consumer Affairs? I don't know the number or web address. Actually, I didn't even know they had such an animal. Matthias Jetleb VA3-MWJ (26 years ago, 14-Jan-01, to lugnet.robotics)
|