 | | Sharp GP2D12 and Expansion Board
|
|
Get a load of this... I have 2 handyboards and 2 expansion boards. I cut the traces to the pull up resistors for analog port 0 on both boards. One handyboard/expansion board worked perfectly with the Sharp GP2D12 analog IR range finder. With the (...) (26 years ago, 1-Dec-00, to lugnet.robotics.handyboard)
|
| |
 | | Looking 4 robosport constructopedia scans
|
|
Hi, I am looking for the mindstorms Robosport constructopedia (scans) if you have them online somewhere let me know thanks Michel (26 years ago, 2-Dec-00, to lugnet.robotics.rcx)
|
| |
 | | Re: motorized points - beating a dead horse
|
|
(...) Well, I'm sure glad I didn't point Steve at this other excellent Lego trains site then: (URL) would have been even more embarassing. Tilman (26 years ago, 1-Dec-00, to lugnet.robotics)
|
| |
 | | Re: motorized points - beating a dead horse
|
|
(...) Tilman, good info for the other folks reading along, but trust me, Steve Barile, as a founding member of PNLTC (either the oldest or second oldest, depending how you measure, Lego Train club ((URL) and grandfather to many of the rest of us (...) (26 years ago, 1-Dec-00, to lugnet.robotics)
|
| |
 | | Re: Results for Aluminum Can Stacking Contest at BrickBots.Com
|
|
(...) [SNIP] (...) I have found that mobile robots, and stationary 'machines' are very different design challenges. A bit over a year ago I had made all sorts of mobile robots and found myself in a rut of building certain structures and units over (...) (26 years ago, 1-Dec-00, to lugnet.robotics)
|
| |
 | | Re: Results for Aluminum Can Stacking Contest at BrickBots.Com
|
|
That first place machine - Wonderful! My congratulations. And a great scheme Rich. It is often a lot more difficult than it looks to make mechanisms as complicated as this work properly. (...) When I first got my RIS a year or so ago, I decided to (...) (26 years ago, 1-Dec-00, to lugnet.robotics)
|
| |
 | | Results for Aluminum Can Stacking Contest at BrickBots.Com
|
|
The Aluminum Can Stacking Contest ended yesterday, it was a ton of fun and here are the highly anticipated (at least for me) results: First Place, stacking 5 cans in 1 minute 25 seconds, earning 6 points Matt with his Stack Master 1000 - (URL) is a (...) (26 years ago, 1-Dec-00, to lugnet.robotics)
|
| |
 | | Old Contest at BrickBots.Com - Aluminum cans
|
|
First I would like to thank Richard Sutherland for Brickbots.com and his Contests. I tried to make a can stacker. I learned a few things first you can never have to many Legos. (Need more). Second his seemly easy contest was a lot harder than it (...) (26 years ago, 1-Dec-00, to lugnet.robotics)
|
| |
 | | Re: motorized points - beating a dead horse
|
|
Michael I can't seem to get to your URL. Can you check it and reply. I really can't wait to see what you have done. SteveB (...) (26 years ago, 1-Dec-00, to lugnet.trains, lugnet.robotics)
|
| |
 | | Re: motorized points - beating a dead horse
|
|
You could try my switch - (URL) out for Lego and Models ... I build this thing using a rubber-band so you can let it run without the switch destroying itself. Just let the motor run a view seconds until the point switches it's position. Michael (...) (26 years ago, 1-Dec-00, to lugnet.trains, lugnet.robotics)
|
| |
 | | Re: motorized points - beating a dead horse
|
|
There's a lot of activity around Lego trains. Clubs, fans, shows, web sites, and lots more. If you look around, you should find some suggestions. Try this page for starters: (URL) a page with some information on point motors: (URL) (26 years ago, 1-Dec-00, to lugnet.robotics)
|
| |
 | | Re: motorized points - beating a dead horse
|
|
(...) (note some heavyhanded snippage) Well, it wouldn't be entirely elegant unless you mounted the mechanics under your substrate, but if you were to gear down the movement so that the white clutch gear had to exert less torque to overcome the (...) (26 years ago, 1-Dec-00, to lugnet.trains, lugnet.robotics)
|
| |
 | | Re: motorized points - beating a dead horse
|
|
Steve, If you are willing to use non-lego parts, there is a reliable solution. You can build a limit switch that does not use any sensor inputs. You need two "normally closed" switches, and two diodes. Solder a diode across each switch. Wire the (...) (26 years ago, 1-Dec-00, to lugnet.robotics)
|
| |
 | | Re: motorized points - beating a dead horse
|
|
Try putting belt drive stage in your geartrain so it can't destroy things and use touch switches to limit the travel... (26 years ago, 1-Dec-00, to lugnet.trains, lugnet.robotics)
|
| |
 | | Re: Communication between NQC and VisualBasic
|
|
In article <G4uLMp.1tL@lugnet.com>, "Richard Sutherland" <richard@webbox.com> wrote: here...it would just be putting another level of abstraction between the (...) IR Messages are implemented, although in the simulated environment they result in (...) (26 years ago, 1-Dec-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Communication between NQC and VisualBasic
|
|
(...) Unfortunately, Spirit.ocx doesn't support sending messages. However, the packet protocol is pretty simple so as long as you can access the serial port directly you should be able to build message packets. See the following web pages for more (...) (26 years ago, 1-Dec-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Using a Sony Remote control to run my Mindstorms...
|
|
Not a problem. J- (...) (26 years ago, 30-Nov-00, to lugnet.robotics.rcx)
|
| |
 | | Re: motorized points - beating a dead horse
|
|
I didn't take pictures, but I did it w/ some gearing and clever placement of a touch-sensor. The key part was that the touch sensor (though light or rotation would work) would sense when the switch was vertical; I then used the motor like a big (...) (26 years ago, 30-Nov-00, to lugnet.robotics)
|
| |
 | | motorized points - beating a dead horse
|
|
Hi All, Currently I am attempting to build an automated hump yard. The main problem I'm tackling is the RCX controlled motorized points. I've spent 7 hours over the last two days trying to build a motorized switch track that will run forever with (...) (26 years ago, 30-Nov-00, to lugnet.trains, lugnet.robotics)
|
| |
 | | Re: SDK2.0 on RCX1.5?
|
|
(...) Yes, the firmware works GREAT in the 1.x bricks. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (26 years ago, 30-Nov-00, to lugnet.robotics.rcx)
|