To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *24649 (-10)
  Re: LinuxPPC and "No response from RCX" problem
 
(...) Did you set the correct permissions for the serial ports (normally they're only accessible by root under Linux) Do a chmod 777 for /dev/ttyS0 (26 years ago, 3-Nov-00, to lugnet.robotics.rcx.nqc)
 
  LinuxPPC and "No response from RCX" problem
 
Hi, I recently bought an RIS kit and from my Windows box it works fine. When I try using LinuxPPC off my PPC Amiga I get the following: [root] /home/chris/nqc/nqc-2.2.r2 >bin/nqc -v -raw 10 Tx: 55 ff 00 10 ef 10 ef Rx: 55 ff 00 10 ef 10 ef Tx: 55 ff (...) (26 years ago, 3-Nov-00, to lugnet.robotics.rcx.nqc)
 
  Re: How2 'count' in NQC
 
In lugnet.robotics, Jerry Kalpin writes: [SNIP] (...) There is an EDGE mode available through the firmware that only counts transitions between pressed and non-pressed (actually some raw threshold value if I remember correctly) states. This sensor (...) (26 years ago, 3-Nov-00, to lugnet.robotics)
 
  Re: How2 'count' in NQC
 
I have noticed this ongoing thread about the difficulties of debouncing and counting switch closures, and I must say that it is a very real problem anywhere electromechanical switches are interfaced to electronics which is orders of magnitude (...) (26 years ago, 3-Nov-00, to lugnet.robotics)
 
  Re: How2 'count' in NQC
 
Steve, this is the third time you have helped me, and this time you obviously spent a lot of time working out the alternatives. First of all, the Wait (DELAY); in my inept code was not to flash every half second. It was to prevent additional counts (...) (26 years ago, 3-Nov-00, to lugnet.robotics)
 
  Re: Radio Controlled Tank - tread lightly.
 
(...) Yes, please! :) Have to check if they sell Funrise brand toys here in Sweden. //Harri Manni -"Do not take life too seriously.You will never get out alive." (26 years ago, 3-Nov-00, to lugnet.robotics)
 
  Re: MOC: Radio Controlled Tank.
 
(...) Here's an idea you can try to have them slip a bit less. Do you have the ordinary chain links too? Then ones without the wide tread? If so use an ordinary chain link for every third link, say. Like this: ##=##=##=##= Perhaps this will give (...) (26 years ago, 3-Nov-00, to lugnet.technic, lugnet.robotics)
 
  Re: MOC: Radio Controlled Tank.
 
(...) Thanks :) (...) Yes, they sure were. One of 'em I even managed to scare twice, first when the tank entered the room and then when it actually fired a projectile :) To bad it takes almost half a minute to set the cannon horisontally, I have to (...) (26 years ago, 3-Nov-00, to lugnet.technic, lugnet.robotics)
 
  Re: MOC: Radio Controlled Tank.
 
(...) Thanks! So do I :) (...) It's from before my dark ages, mainly the 8851 Excavator and the 8660 Arctic Rescue, I also got two with the 8843 Fork Lift truck. They usually look better then they work since they tend to slip a lot, but in this case (...) (26 years ago, 3-Nov-00, to lugnet.technic, lugnet.robotics)
 
  Re: Palm Hardware Interface idea? + other stuff
 
(...) It's basically the same serial data connection as the RCX. It just uses radio for transmission instead of infrared, so it goes around corners and has a longer range. Jürgen (26 years ago, 3-Nov-00, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR