 | | need advice on joining....
|
|
Help I am building a gripping mechanism and am using pneumatics to do the squeezing. Due to the orientation of the hole on the base of the cylinder I was "forced" to attach a beam in such a way that is now puts me in a bind. The beam in question (...) (26 years ago, 7-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Dropping your RCX on the floor...
|
|
Not if was on when that battery disconnects. I think the memory is powered through a capacitor or somthing like that, when the RCX if off the power to the memory is maintained even when batteries arn't in for a few minuets because of the small (...) (26 years ago, 7-Oct-00, to lugnet.robotics.rcx)
|
| |
 | | Re: Dropping your RCX on the floor...
|
|
Yes, it was on, and when I picked it up, it was turned off. I thought "No! It's broken!" but you could turn it on, and the firmware was gone. But doesn't the batteries need to be disconnected for like a minute for the firmware to be erased from (...) (26 years ago, 7-Oct-00, to lugnet.robotics.rcx)
|
| |
 | | Re: legOS doesn't work under NT?
|
|
(...) are some (...) problems, (...) Absolutly Yes. (...) 0.2.3 and (...) memcpy.c. I (...) to (...) Begin from these two URLs: (URL) Paolo. --- Indecision is the key to flexibility. (26 years ago, 7-Oct-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: More on Miniboard woes and woohoos.
|
|
The current version of ICC11 has a builtin downloader that talks to MB. Only for W95/NT/... though. ICC11 works with just about ANY HC11 boards, minus lack of support for paging. (...) -- // richard (URL) (26 years ago, 7-Oct-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Dropping your RCX on the floor...
|
|
(...) I've "dropped" my RCX & Scout a few times... Mostly when an invention suddenly speeds with all it's might off the table and onto the floor. I've been very lucky not even lost firmware. I had a kid drop the Lego remote and it popped apart. I (...) (26 years ago, 7-Oct-00, to lugnet.robotics.rcx)
|
| |
 | | Re: Dropping your RCX on the floor...
|
|
Having had to dismantle an RCX at one stage, I would point out that the battery connectors are not solidly attached to the main circuit board inside the RCX. (I have noted a lot of Lego electrics are built along those lines - relying on mechanical (...) (26 years ago, 6-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Dropping your RCX on the floor...
|
|
(...) Loss of firmware... perhaps the batteries temporarily lost their connection when you dropped the RCX? Was the RCX on at the time? -Kekoa (26 years ago, 6-Oct-00, to lugnet.robotics.rcx)
|
| |
 | | Re: NQC versus Lego RCX Code Speed
|
|
(...) With regards to your comment about sensor watchers, yes they are slow. If I remember correctly, they are implemented by a task that loops forever polling the sensors and starting other tasks whenever an event of the proper type occurs. Tasks (...) (26 years ago, 6-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Linux and handyboard help!
|
|
I got it!! Thanks! I was loading the wrong library. I had the correct library in the directory, but I hadn't run ic -config and changed it. Thanks again. ___...___ Jesse Dosher, K7DSP University of Washington, Dept. of Electrical Engineering, (...) (26 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|