To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *23439 (-10)
  Re: External supply for RCX
 
(...) The only issue with the standard rechargeable ones is if the motor(s) short the resulting current drain could damage something. I'm sure we've all shorted a rechargeable and had the rubber wire casings melt off from the 'heated exchange'.. (...) (26 years ago, 5-Sep-00, to lugnet.robotics)
 
  RE: RCX IR-Tower and Vision Command
 
This has been noticed before. I would guess that it is the result of an engineering change on the PC board, well after the molds for the tower plastic parts had been machined. They (TLG) probably tried it out, found it worked anyway, and didn't (...) (26 years ago, 4-Sep-00, to lugnet.robotics)
 
  Pcode source code; disabling the LCD
 
Hi all, Does anyone have a copy of the pcode source for IC 3.1? According to an earlier posting, it used to be available on the Newton Labs FTP site, but it's not there anymore. Also, has anyone ever completely disabled their LCD? Even after the (...) (26 years ago, 4-Sep-00, to lugnet.robotics.handyboard)
 
  Re: Here's the Rover with handyboard
 
Hello Jerry, Did not get the picture of the Mars Rover. Sounds like you have a good start on your robot, please keep us advised on the problems and solutions. Was it hard to convert the mice encoders?? should be very accurate, please post the (...) (26 years ago, 4-Sep-00, to lugnet.robotics.handyboard)
 
  Re: Limited slip differential
 
(...) How about this for a thought - I remember reading somewhere about using the differential to keep a tracked vehicle on a straight path using one rotation sensor: (URL) using another differential in this capacity, it should be possible to detect (...) (26 years ago, 4-Sep-00, to lugnet.robotics)
 
  Re: Limited slip differential
 
(...) Nice :-) (...) Time for the pedant to strike again - I think you are right in saying that this part serves a similar purpose to a synchro in a real car, but the real one gradually sychronises the speeds of the axle and the "idler" gear so that (...) (26 years ago, 4-Sep-00, to lugnet.robotics)
 
  Re: External supply for RCX
 
(...) quite a (...) compared (...) I regularely run my RCXs on NiMH Sanyo rechargable batteries and they works very well. Voltage is lower, but they're much more current capable then the alkaline technology ones. Ciao Mario (26 years ago, 4-Sep-00, to lugnet.robotics)
 
  Here's the Rover with handyboard
 
Attatched is a picture od the toy Mars Rover that I am modifying. Right now I have the handyboard driving two lego motors and I ripped apart a mouse to use the encoder. Mice encoders sure work great! And they are much cheaper than commercial (...) (26 years ago, 3-Sep-00, to lugnet.robotics.handyboard)
 
  Re: Vision Command
 
the color sensing software works great recognizing greens, blues & reds. It has a hard time recognizing black. which kind of hinders my project of making a self recognizing robot. (it has a hard time recognizing the lens section) lighting - (...) (26 years ago, 3-Sep-00, to lugnet.robotics)
 
  Re: Limited slip differential
 
Now I see it. I found the gear you were talking about on the Technica site. This if very serendipitous, as I have recently been pondering how to make a locking diff with Lego. Thanks for the intel! - Greg Simon Bogaert wrote: <snip> (...) (26 years ago, 2-Sep-00, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR