 | | Re: rotation sensor problem, again...
|
|
I had the same problem and I solved it with a msleep(50). msleep(10) is not enough. (...) (26 years ago, 3-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: battery life indicator
|
|
if((BATTERY/0x0016)<700) dlcd_show(LCD_BATTERY_X); I always put this line on my programs. BATTERY/0x0016 gives the value in V*100 of all batteries open circuit voltage. <700 is the limit for rotation sensors to work (all the other sensors have (...) (26 years ago, 3-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
 | | 6.8nF Capacitor
|
|
I have got all the parts for building my HB except for a 6.8 nF 2% capacitor (component C6). Maplin Electronics have stop doing it and I am not sure where to try next. I am in the UK, does any body know if I can change the resistors in the infrared (...) (26 years ago, 3-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: running motors underwater
|
|
Cool Idea, but take it to it's logical extension ... Use the technic pnuematic elements to maintain positive air pressure in the motor housing. If you pump air into the tubes that you mentioned at a pressure higher than the water pressure, it will (...) (26 years ago, 3-Jul-00, to lugnet.robotics)
|
| |
 | | Re: running motors underwater
|
|
(...) It depends alot on what kind of water it's in. Pure distilled water doesn't conduct very well. Water with any kind of ions (salt chlorine, flourine etc) will conduct much better and cause more heating. In addition, the electrolisis that occurs (...) (26 years ago, 3-Jul-00, to lugnet.robotics)
|
| |
 | | Re: running motors underwater
|
|
(...) This sounds like a great application for temp sensors. :) I don't know if this has been brought up on this site before (it probabably has), but it might work pretty well to place a temp sensor directly against a motor's case, to measure the (...) (26 years ago, 3-Jul-00, to lugnet.robotics)
|
| |
 | | running motors underwater
|
|
I haven't tried this myself, but I was just thinking that there could be many reasons why the motor heats up after running underwater. But first, do we know for sure that they are heating up more than they normally would? It would be interesting to (...) (26 years ago, 2-Jul-00, to lugnet.robotics)
|
| |
 | | Re: interrupts for buttons
|
|
Sorry about the long delay, I've been away. Demo.c is inaccessable because it was written for 0.1.7 and I've not yet had the time to update it. Unfortunately, this is going to be a semi-major task and so will probably be one of the last things to (...) (26 years ago, 2-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: running the motors underwater
|
|
Are your tank filled with salt water? What is the electro-conductivity of your water? By the way, sinking a motor under water will damage lubricant inside the motor. I suggest you to pack the whole mechanic into a metal case, and seal the metal case (...) (26 years ago, 2-Jul-00, to lugnet.robotics)
|
| |
 | | RE: running the motors underwater
|
|
I have run the Lego motors for long enough that they have gotten warm. This tells me that the holes you want to plug up would be needed as air vents. Not as much for circulation, but to let the air in the motor escape when it heats up and becomes (...) (26 years ago, 2-Jul-00, to lugnet.robotics)
|