To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *22244 (-10)
  Re: LNP Question
 
Hello Colin, (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
 
  Re: HB Memory map
 
Device Location Notes ===...=== 6811 internal $0000-$00ff Built-in RAM (A1 chip) $0000-$01ff (E1 chip) ---...--- 6811 control $1000-$103f Built-in registers ---...--- Expansion I/O $4000-$4fff Memory reads in this range enable the Y1 latch selector, (...) (26 years ago, 14-Jun-00, to lugnet.robotics.handyboard)
 
  Re: LNP Question
 
"Colin Ryan" <colin.ryan@cs.tcd.ie> ha scritto nel messaggio news:394758BE.3DEA88....tcd.ie... (...) I'm working to a porting of lnpd for Win32, but it's not finished yet... Bye, Paolo. --- Indecision is the key to flexibility. (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
 
  Re: Interfacing BASIC Stamp and Lego?
 
In a flee market, I stumbled upon an Swedish electronics magazine with Lego on its cover. Of course, I had to buy it. :) The article's header read: "LightFinder - Controlling Robots using BASIC Stamp". The article is of course in Swedish but if (...) (26 years ago, 14-Jun-00, to lugnet.robotics)
 
  Re: Motors spinning at startup
 
The problem is the same with LEGO-gear-motors. Even worse, the post says "... put a wire to the can ..." but how can you do this with a plastic device? Any help appreciated. Dirk (26 years ago, 14-Jun-00, to lugnet.robotics.handyboard)
 
  LNP Question
 
Hi All, Apologies if this should be obvious., but I'm curious as to how I can build a windows based LNP application, can it be done? I see that most LNP discussions to date are Linux and LNPd oriented, which would lead me to believe that my only (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
 
  Re: Help needed: Problems setting up the IR tower
 
(...) Have you already tried with a new 9V battery in the IR tower? Antonio (26 years ago, 14-Jun-00, to lugnet.robotics.rcx)
 
  Re: Help with make in Windows
 
Ah...progress. I have finally started tracing the function calls. Did I mention my head hurts? :-p Seriously, what I found was in the 0.2.2 on Windows Instructions, number 8 says "Change the CINC variable definition in legOS\Makefile.common to (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
 
  Re: legOS built on NT - what now
 
Colin, what version of legOS did you install? -- Gary (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx.legos)
 
  Re: Help needed: Problems setting up the IR tower
 
I have tried both Andi Scharfstein´s and Reinis Kanders´ recommendations and everything seems ok but there was no improvement... The comm port works fine with my PalmPilot craddle but not with my IR tower...Does anyone else have another (...) (26 years ago, 14-Jun-00, to lugnet.robotics.rcx)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR