 | | arbitrary motor code
|
|
Did anyone ever write the wrapper to allow motor_dir(motor_label x, MotorDirection dir) or some such? There was a variant of it way, way back (0.1.5?) but I don't see anything like it in the current CVS code. Anyone? Anyone? -Luis ---...--- "Going (...) (26 years ago, 20-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Interface B & Lego Engineer
|
|
Is anyone using the Lego Dacta Interface B and the Lego Engineer Plug-in to Robolab 2.0? Can the interface B source enough current to actually drive 8 motors? Does Lego Engineer/Interface B provide all the functions that Robolab 2 does with the RCX? (...) (26 years ago, 20-May-00, to lugnet.robotics)
|
| |
 | | Question Droid Developer Kit
|
|
I am writing assembly instructions for a person that is totally blind. These are for the Droid Developer Kit. The person will not be able to experience the digital display. My question is "does the display default to a certain program number when it (...) (26 years ago, 20-May-00, to lugnet.robotics)
|
| |
 | | Re: lnp communication question
|
|
(...) Ok, this brings up more questions :). I have never had any problems with errors when sending messages. Sometimes the message is not recieved but when it is, I have never seen any errors in the transmission. Am I missing your point? Second, (...) (26 years ago, 20-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Sharp analog distance sensor
|
|
Greetings, I've looked, but don't seem to be able to find any relevant info. How does one hook up one of these beasts to the handyboard? I remember reading something somewhere that a track needs to be cut to do this - something I would like to avoid (...) (26 years ago, 20-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Quick Q : 9v Motors
|
|
(...) There's a big difference - some of the details are here: (URL) Baum (26 years ago, 20-May-00, to lugnet.robotics)
|
| |
 | | Re: IR communication PC <-> brick with NQC
|
|
(...) The RCX uses a special packet protocol which involes a lot of binary (non-ASCII) bytes, so controlling it with Hyperterminal won't work very well. Your best bet is to either write your own code to send the packets of the serial port or just (...) (26 years ago, 20-May-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Is there a compatible h8 assembler for forth words?
|
|
(...) A good rule. I just know I'm going to need fast so I am planning ahead. Somehow I'm usually at the bleeding edge of trying to squeeze everything possible out of limited hardware. I originally learned my Forth on a 68000 (Mac Forth on the (...) (26 years ago, 20-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: Spirograph Formulas??
|
|
You might enjoy the book "Turtle Graphics" - (URL) - uses the Logo language to control robotic turtles - descibes everything not in the mathematics of analysis but in terms of local geometric movement. Not sure if it has spirograph in it or not, but (...) (26 years ago, 19-May-00, to lugnet.robotics)
|
| |
 | | RE: Is there a compatible h8 assembler for forth words?
|
|
(...) No there is not. That being said, it's pretty easy to write one...if you have the time. I fiddled around with it a bit and then gave up since the GNU tools worked pretty quick. It was strictly a time/value exchange. From bitter experience, (...) (26 years ago, 19-May-00, to lugnet.robotics.rcx.pbforth)
|