 | | Re: local variables
|
|
(...) This is completely true and is basically a feature of the C language. Globals aren't technically "initialized" at all. They are just loaded as part of the image. You could consider that they are initialized at compile time. On a workstation OS (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Help with Terminal Emulator
|
|
I'm just getting started using pbForth, and I'm having trouble with the terminal emulator echoing garbage on the screen with almost every key stroke. I've tried all of the suggested terminal emulators with the same results, including hyperterminal, (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Re: how many servos on handyboard?
|
|
Ray, Whoops, just read my message again, and realised I had stated STEPPER motor, and not the intended SERVO motor. I have used the HB to control 4 SERVO motors. The SERVO's had an external 5V power. The GND of the SERVO supply was attached to the (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | RCX2 What are people doing?
|
|
I'm a bit bored and this list has been very quiet. So what are you doing with NQC2 everybody? James P (27 years ago, 17-May-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: New pbForth GUI
|
|
(...) need (...) the (...) Maybe...I'll keep you informed :-) In the meanwhile I tested your GUI on a Win2000 machine (version 5.0, build 2195). Same procedure, same positive result. Mario (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: New pbForth GUI
|
|
(...) Great! Maybe I can get another convert over to the dark side... The script uploads should work well too. And definitely try the SAVE-SYSTEM download. You need to load bigsys.srec firmware. Just type SAVE-SYSTEM after you've added whatever (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RF vs IR link
|
|
Just a naive question: How much difficult would be to use the RF Cybermaster link with the RCX? (27 years ago, 17-May-00, to lugnet.robotics.rcx)
|
| |
 | | Re: lnp communication question
|
|
Remember the medium... cheap IR basically stinks for transmission. You get transients from the lights in your room, the outdoors, yadda, yadda. Luis (wishing for RF like the Europeans get ;) (...) ---...--- "Going to California with an aching in my (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: New pbForth GUI
|
|
(...) Just to confirm that, I successfully installed the GUI in my NT system (NT4.0 Build 1381, SP 5) following Jeff's procedure. It works great, no need of the giveio driver, no problems with the COM port though not having the Admin rights. Thanks (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: how to drive extra steppers with handyboard
|
|
i ended up using two SSC II's to control the twelve servos on my robot because most of the time the servos connected to the XB would not work. the SSC II servos worked almost all the time. (URL) think this is the web address and the SSC II's connect (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | RE: New pbForth GUI
|
|
Jeff wrote... (...) Thanks Jeff, I was worried it might be taken the wrong way after I posted it... (...) I've snipped the rest of the description, but the result is that it works without the giveio driver, if I understand correctly. This is VERY (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: how to drive extra steppers with handyboard
|
|
Try Scott Edwards SCC II Servo controller. (...) This message is for the named person's use only. It may contain confidential, proprietary or legally privileged information. No confidentiality or privilege is waived or lost by any mistransmission. (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Expansion board cannot handle more than 2 servos
|
|
Hello, Reading the discussion on servos recently, I thought I'd share this info with you. I have advised a few student group projects involving servos and the XB and came to the conclusion that the XB cannot handle more than two or so servos. The (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Scout, Microscout & IR Remote
|
|
Dennis Williamson <dennis.NO@SPAM.netstrata.com> wrote (...) You're right. Sorry, my fault. There had been so much talking about this feature between the end of 1999 and the beginning of 2000 that I thought Eric's page included this info too, and (...) (27 years ago, 17-May-00, to lugnet.robotics)
|
| |
 | | RE: how many servos on handyboard?
|
|
Remeber also that you have to cut the motor power trace and use an external 5V source for the motors in this case. The HB itself will output 9.6 V from the motor ports. (...) This message is for the named person's use only. It may contain (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: lnp communication question
|
|
(...) This suprises me. I have never heard of such high packet losses. How does dll do this? With some kind of ack and retry mechanism? dll seems reliable. Of course dll is going in the other direction. (27 years ago, 17-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | RE: New pbForth GUI
|
|
Ok, Ok, I'm an idiot....this is such a polite group that no one ever says RTFM ;>) Well, you did Ralph, but very, very nicely.... This GUI works great in NT (NT4.0 SP3), with very little work (once you start to think). Download and unzip TclTk ( I (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | how to drive extra steppers with handyboard
|
|
I'd like to build a six legged robot. that would need at least 12 servos. Is there a way to control 12 servos or more with the standard handyboard? someone said it's all in the code (using digital outputs) does that mean I could write the code to do (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Scout, Microscout & IR Remote
|
|
I didn't find any reference to the Microscout on his site. Dennis (...) Bad News: The next millenium starts on a Monday. Good News: You get the day off. (remove .NO and SPAM. to reply) (27 years ago, 17-May-00, to lugnet.robotics)
|
| |
 | | Re: how many servos on handyboard?
|
|
(...) Hi If you use the expansion board, you will loose analog input 0 und 1. These two inputs are multiplexed on the exp board, so you get some more analog ports. -Martin (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|