To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *21759 (-20)
  RE: New pbForth GUI
 
Jeff Hazen wote: (...) Me too. I got tired of dinking around with HyperTerminal... I'm not sure at all about an NT installation, so I'm hoping some others will step in here... (...) No, If you unzip the distribution, there should be a .lnk file (...) (27 years ago, 16-May-00, to lugnet.robotics.rcx.pbforth)
 
  how many servos on handyboard?
 
I'd like to know how many servos the handy board can control. On the FAQ it says 2, in the documentation it says 4 DC motors. what's the deal? (am I stupid? I'm new at this) also, when you plug an expansion board, do you get 6 EXTRA servos? or those (...) (27 years ago, 16-May-00, to lugnet.robotics.handyboard)
 
  local variables
 
Hi! I read that legOS only declared varibles the first time the program is run. Does this mean I cannot use local variables. I have loops in different functions using 'i' as looping variable, which is locally declared. Should I avoid this? Tobias (27 years ago, 16-May-00, to lugnet.robotics.rcx.legos)
 
  RE: New pbForth GUI
 
This is a great idea, Ralph. I've wanted to just fool around in pbForth, but have been intimidated by the apparent front-end learning curve. I'm a mechanical guy, I don't do TclTk, Gnu, etc., I've been spoiled by GUI front ends and install programs. (...) (27 years ago, 16-May-00, to lugnet.robotics.rcx.pbforth)
 
  Re: Scout Questions
 
The others have mentioned the white gear is a clutch gear. I thought I'd throw out a practical use to put it into perspective: it's ideal for a motorized gripper, where you'd want the grip to have some resistance as it closes, but not so much torque (...) (27 years ago, 16-May-00, to lugnet.robotics.scout)
 
  Re: Ultrasonic maximum timing
 
(...) Except that I don't think it counts at 2Mhz, rather I think it counts at 500Khz (2 / 4 = ECLK) (I may be totally off base here, since I've not read the pink book in about 6 years) that would put your max at 32767/500000 = .0655 at 1000 ft/sec (...) (27 years ago, 16-May-00, to lugnet.robotics.handyboard)
 
  Re: Ultrasonic maximum timing
 
(...) I think the register maxes out at 32767. Since it's a 2 MHz processor, this gives: (32767 cycles) / (2,000,000 cycles/second) = 0.01638 seconds Up here in the Rocky Mountains, the speed of sound is about one centimeter every 143 (...) (27 years ago, 16-May-00, to lugnet.robotics.handyboard)
 
  Re: proposed new word for deleting pbforth
 
(...) As a guess the following string tells the ROM that there is valid firmware. This might need to be stepped on before jumping to the reset vector. .string "Do you byte, when I knock?" (27 years ago, 16-May-00, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
 
  Re: lnp communication question
 
(...) So the length-argument tells lnp_integrity_write how many bytes to send? Doesn't that mean that it would be possible to send an array consisting of many integers, for example? How would this be done? (...) We plan to build a six-legged lego (...) (27 years ago, 16-May-00, to lugnet.robotics.rcx.legos)
 
  winlegos compiler problem
 
I am trying out the lnp functionality with addressing and such, and of course I had to recompile the legos kernel. That, in itself, seemed to go without a hitch, but when I later tried to compile one of the demo programs, this is what I got. djecho (...) (27 years ago, 16-May-00, to lugnet.robotics.rcx.legos)
 
  RE: proposed new word for deleting pbforth
 
(...) Kekoa, feel free to jump in here... Personally, I think just jumping to the reset vector 0x0000 should do a total cold start, right? Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) ---...--- Reply to: (...) (27 years ago, 16-May-00, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
 
  proposed new word for deleting pbforth
 
It would be handy if there was a word that deleted firmware. It is often inconvenient to get at the batteries. At Kekoa I see the opcode but no rom entry point. Trashing the header in memory and jumping to the reset vector might do it. I wonder if (...) (27 years ago, 16-May-00, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
 
  RE: More linux feedback. firmware upload doesn't work for me.
 
(...) This is wierd. I had it working on my Caldera Linux 2.2 which has TclTk 8.0.4 I'll try again. One of the problems is that I can't seem to get a nice NFS system running here, and I have to FTP the files around... :-( I'll try and make a better (...) (27 years ago, 16-May-00, to lugnet.robotics.rcx.pbforth)
 
  Re: Quick Q : 9v Motors
 
The motor in the 8735 pack (known individually as the 5225) is a much newer design that includes some built-in gear reduction and a flywheel. It has a fairly low speed, but high torque. The motor in the 8720 pack (known individually as the 5114) is (...) (27 years ago, 16-May-00, to lugnet.robotics)
 
  Re: Quick Q : 9v Motors
 
From my understanding, the 8735 is a geared motor, with more torque, but less RPMs than the 8720. Quite a bit of difference between the two, I think. Sorry, but I don't know the specifics other than that. -Andy Lynch (...) between (...) (27 years ago, 16-May-00, to lugnet.robotics)
 
  More linux feedback. firmware upload doesn't work for me.
 
Firmware download is not working. I'm sorry but I never tried this with the first release. A second problem is that it gives no error message if the firmware download fails. I got suspicious because the download was too fast and the LCD was not (...) (27 years ago, 16-May-00, to lugnet.robotics.rcx.pbforth)
 
  Quick Q : 9v Motors
 
Is there any difference, in terms of performance and power consumption, between the 8735 and 8720 motors. Or is it the same electrics in a different case? Scott A From www.brickset.co.uk - The 8735: (URL) 8720: (URL) (27 years ago, 16-May-00, to lugnet.robotics)
 
  Re: New pbForth GUI; linux feedback
 
(...) o - When will 1.2.0 sources be available? I'd rather be working from current stuff. Does the gui depend on this version of pbforth? o - rcxtk.tcl should have executable permission in the tarball. This can be done with the -p flag to tar (...) (27 years ago, 16-May-00, to lugnet.robotics.rcx.pbforth)
 
  Ultrasonic maximum timing
 
Greetings all, I'm using a homebuilt sonar based on Kam Leang's design, which seems to be working quite well. I just have one question with regard to the timing on the input port. I'm using the same sonar driver as for the polaroid - right now I (...) (27 years ago, 16-May-00, to lugnet.robotics.handyboard)
 
  New pbForth GUI
 
I'd like to announce the availability of an early trial version of a GUI for pbForth. It's written in TclTk, a free scripting language, but that's transparent to the user. (URL) The GUI runs under Windows and Linux, and as soon as I can find a (...) (27 years ago, 16-May-00, to lugnet.robotics.rcx)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR