To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1471 (+10)
  LMD18200 Motor driver
 
Is there a way to use the LMD18200 motor driver as a replacement for the motor chip on the handyboard? I know that they are not pin compatable but is there some type of interface that can be built easily? Thanks. Keith Keith Soldavin (...) (30 years ago, 14-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Motors & handyboard
 
(...) Unfortunately this is the LEAST amount of current the motor will draw when operating. You have measured the 'unloaded current'. Now, while you have your motor running, grab the shaft between your fingers and stop it, and measure that current. (...) (30 years ago, 14-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Automatic feeding.
 
(...) Here's an idea for you: For a mechanical system you could use two 'wiskers': one on top and one on the bottom of the 'bot. (Or one each side.) You set up the 'feeding pen' to be two parallel metal plates. Set them up so that the 'bot can roll (...) (30 years ago, 14-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Motors & handyboard
 
(...) EE Question: How do you use a multimeter to measure the current? I was told that you need a current probe to do this kind of thing. ?? (30 years ago, 14-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Automatic feeding.
 
(...) One way that I did this was to steal an idea from the railroad world. (...) In my case I put a conductor (a wire) around the outside of my two drive wheels. At the top of the wheels was a 'brush' (which was a simple spring loaded contact) and (...) (30 years ago, 15-Feb-97, to lugnet.robotics.handyboard)
 
  (no subject)
 
Please unsubscribe me Matt Enser Director DLR Windows95 Lab email : menser@sbu.edu WEB: (URL) (30 years ago, 15-Feb-97, to lugnet.robotics.handyboard)
 
  Re: expansion board
 
(...) I can vouch for this technique, this is basically what I do in my PIC program (except the randomness which is a nice touch BTW) and get rock solid detections. When the frequency is spot on to the center frequency (38Khz for the 1ISU60's) and (...) (30 years ago, 15-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Motors & handyboard
 
Guys, I caught the mail on motors (3V etc.) and wasn't impressed. I just bought one of those Bulldozer Kits from Tamiya and I believe it contains 3V motors. Is there NO possible way of using these motors??? I did notice the HB motor driver chip (...) (30 years ago, 15-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Motors & handyboard
 
To measure current with an multimeter or ammeter (volt/ohm/etc.. meter) you must break the circuit at some point and put the meter in series with the circuit thus gapping the break. ie) +-----(+) METER (-)------+ | | | | (+) | POWER | (-) | | | | | (...) (30 years ago, 15-Feb-97, to lugnet.robotics.handyboard)
 
  Motors, gear boxes, tools
 
Greetings: on the Hanyboard web page, Tower Hobbies is mentioned as source for RC supplies etc. I would reccommend highly for electric motors, gear boxes, tools including a nice metal turning lathe, Hobby Lobby International www.hobby-lobby.com (...) (30 years ago, 15-Feb-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR