To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *14396 (+20)
  Serial transmiter
 
Does anyone know of a 9600(8,N,1) serial port transmitter? Or have plans for one? I need one for a telepresence robot that I am designing, Also it needs to be as high of power as it can be I am a HAM novice if it makes a difference Andrew Holland (...) (27 years ago, 25-Sep-99, to lugnet.robotics.handyboard)
 
  sensor info
 
Thought I'd pass along this page. (URL) of info on lots of diffrent sensors. (27 years ago, 26-Sep-99, to lugnet.robotics)
 
  Rcx 1.0 vs Rcx 1.5
 
Hi My RCX is a 1.0 What is a 1.5 ? Whats the difference and can mine be upgraded or new software added? Thanks -Mike (27 years ago, 26-Sep-99, to lugnet.robotics)
 
  Re: Rcx 1.0 vs Rcx 1.5
 
(...) Hi, Mike! Check out (URL) can upgrade to 1.5. It's only a matter of PC software and manuals. Søren (27 years ago, 26-Sep-99, to lugnet.robotics)
 
  Re: Rcx 1.0 vs Rcx 1.5
 
(...) "and extra LEGO blocks (including special new connector pieces)." (27 years ago, 26-Sep-99, to lugnet.robotics)
 
  How To Add A Rotation Sensor and A Touch Sensor On the Same Input?
 
Does anyone know how to add a rotation sensor and a touch sensor on the same input of the RCX? Thanks a lot in advance. (27 years ago, 26-Sep-99, to lugnet.robotics)
 
  Re: How To Add A Rotation Sensor and A Touch Sensor On the Same Input?
 
(...) This doesn't work as well as putting a touch sensor and light sensor on the same port. The data that the light sensor sends back (a value normally between 40-80) is easy to distinguish from that sent by the touch sensor (0 or 100, if you have (...) (27 years ago, 26-Sep-99, to lugnet.robotics)
 
  Re: How To Add A Rotation Sensor and A Touch Sensor On the Same Input?
 
I already succesfully put a touch sensor and a proximity sensor (a light sensor and an IR port) on the same input. I tried some different configurations to get a touch sensor and rotation sensor on the same input but it didn't work. I'm wondering if (...) (27 years ago, 26-Sep-99, to lugnet.robotics)
 
  Re: How To Add A Rotation Sensor and A Touch Sensor On the Same Input?
 
(...) Yeah, as I said, the light-sensor/touch-sensor combo works well because of the types of values the sensor returns. The rotation sensor works differently, and is difficult to combine with something else. (27 years ago, 26-Sep-99, to lugnet.robotics)
 
  Re: Robot lab
 
It is much better than the mindstorms software and has three levels of difficulty. It is well worth the extra money. Jim Clark (...) -- There is Love in the Red Letters. There is truth in the Red Letters. There is hope for the hopeless, tears and (...) (27 years ago, 27-Sep-99, to lugnet.robotics)
 
  Re: Robot lab
 
(...) So, you would recommend it for young children? (27 years ago, 27-Sep-99, to lugnet.robotics)
 
  Re: Robot lab
 
Does anybody know if the Robot Lab uses the same spirit.ocx as the RIS? Howbout the new RIS 1.5 version, is the spirit.ocx still the same? -- et Jim & Linda Clark <lego-robotics@crynwr.com> wrote in message news:37EEC609.BFFC86...oot.com... (...) (...) (27 years ago, 27-Sep-99, to lugnet.robotics)
 
  Re: Robot lab
 
(...) Robolab doesn't use spirit.ocx. It does use the exact same RCX and firmware, however. Dave Baum (27 years ago, 27-Sep-99, to lugnet.robotics)
 
  Analog I/O as Digital I/O
 
Can the analog input lines be used as a digital input lines (if there is no requirement of analog input)? Because, these lines are connected to the port E of 68hc11, then what are modifications required in the code? Asim Kar. City University of Hong (...) (27 years ago, 27-Sep-99, to lugnet.robotics.handyboard)
 
  Re: Analog I/O as Digital I/O
 
(...) Since the analog inputs read voltage levels, you should be able to just plug in any switch or 5-0volt input directly. To read the values, use the analog command, and in theory you should only get two possible values, 255 for +5volts, and 0 for (...) (27 years ago, 27-Sep-99, to lugnet.robotics.handyboard)
 
  LEGO Info.
 
I've done an inquiry to the LEGO hot-line ( mailto:hotline@lego.com ) and here are the answers about several topics that might be of interest to some of you: - As from November 1st the new Robotics Invention System 1.5 will be available at LEGO (...) (27 years ago, 27-Sep-99, to lugnet.robotics)
 
  Re: Analog I/O as Digital I/O
 
Also, the "digital(int p)" extends to the analog ports too. When used with a port that is analog in hardware, it just uses 127 as a threshold value to return 1 or 0 (note below 127 returns true). See page 22 in the HB manual. However, with this (...) (27 years ago, 27-Sep-99, to lugnet.robotics.handyboard)
 
  R: Save arrays in VB5
 
If you dimension an array of (say) 100 elements as : DIM a(100) as integer the array elements goes from 0 to 99, for a total of 100. So if your loop searches for a 100th elements it comes out with the "subscript out of range" error. Either restate (...) (27 years ago, 27-Sep-99, to lugnet.robotics)
 
  Re: R: Save arrays in VB5
 
(...) Actually, when you say Dim a(100) as integer, the array contains 101 elements ranging from element 0 to element 100. By default VB starts arrays at the 0th element (this can be changed). The Dim statement for arrays doesn't specify the number (...) (27 years ago, 27-Sep-99, to lugnet.robotics)
 
  5VDC Voltage Regulation
 
I'm in over my head with a project and need some help. I'm trying to use an RCX output port to control a 5VDC SPDT Relay from Radio Shack (part #275-240A). I need to limit the voltage of the port to 5 volts. How can I accomplish this? Is a voltage (...) (27 years ago, 27-Sep-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR