 | | Handyboard debugging problem...
|
|
One of the student groups in my Lego robot course is having a problem getting their Handyboard to work...they got IC to load successfully, then went ahead and installed U6 ('HC138), U9 ('HC04), U5 ('HC244), resistor packs RP1 and RP2, and SW2. Now (...) (30 years ago, 4-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | Extra power supply?
|
|
I can't seem to locate the 'how to add a second power supply for a servo' information. I know I read it once, but now that I want to go back and use it of course I can't find it. (duh) Can anyone point me in that direction? Also I could use any (...) (30 years ago, 4-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR sensors
|
|
(...) Sure. We put "Front" on digital(14) and "Right" on digital(15). And you can have as many as you want that don't interfere with each other. We did something like... contact = digital(14) * 2 + digital(15) to get both sensor results into an (...) (30 years ago, 5-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | QRD1114?
|
|
In the documentation for connecting sensors and actuators to the HB a The Quality Technologies IR reflective optosensors (QRD1114 & QRB1114) were depicted in the example and recommended. Where can these sensors be aquired? Thanks JTW (30 years ago, 5-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | Polaroids
|
|
My design team would like to incorporate two polaroid sensors with our handy board. We were wondering just how do we send the INIT pulse from the HB to the Polaroid sensors? The member in charge of writing the code for our robot quickly drafted up (...) (30 years ago, 5-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polaroids
|
|
Jim, Check out the following links, the work has already been done for you! ftp://cherupakha.med...trib/kent/ ftp://cherupakha.med...ent/readme - Prabal (...) (30 years ago, 5-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | SPI
|
|
Hi all- I remember reading something about an asynchronus serial routine at 1200baud using the SPI that was coming out in January. Does it exist? If so, how can I get it? Does anyone have anything that transmits RS-232 on the HB? I still want to be (...) (30 years ago, 5-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: QRD1114?
|
|
Digikey. call 1 800 DIGI KEY. add 'QT-ND' to the part number and you get the digikey catalog #. -fred In your message you said: (...) (30 years ago, 5-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | Downloading problems
|
|
After setting the CONFIG register, downloading the pcode never completes. We get anywhere from 0 to about 1600 bytes transferred, then an error. Everything has checked out to this point. Any hints? ***...*** * Greg Starr, Professor and Graduate (...) (30 years ago, 5-Feb-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Downloading problems
|
|
The memory circuit is probably flaky, or, you zapped a 6811 address line output. If you haven't already tried, swap the 6811 with a known good one. If that doesn't work, examine the ram chip addr, data bus, and select signals with a logic probe when (...) (30 years ago, 5-Feb-97, to lugnet.robotics.handyboard)
|