 | | Re: I/o's expansions for the mindstorm ?
|
|
(...) This might not be relevant for everyone out there, but I thought I'd point out: If you use a learning remote to learn the codes from the MindStorms remote control, please note that all combinations of the three motor controls send out a (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
|
| |
 | | Re: new products (Remote Control)
|
|
(...) 1 Send message "1" 2 Send message "2" 3 Send message "3" A^ Run motor A in > direction (see notes below) Av Run motor A in < direction (see notes below) B^ Run motor B in > direction (see notes below) Bv Run motor B in < direction (see notes (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
|
| |
 | | Re: IR-Tower and PowerBook-G3 ?
|
|
(...) Yes. The PB-G3 is plugged into a wall-wart almost all the time. I thought of that also. Very strange. I'm resurecting an old SE/30 in the hopes that I can squeeze MPW into an 8MB machine. I think the serial ports on that machine ought to be (...) (27 years ago, 10-Aug-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Pnuematics: e-switch and thoughts
|
|
(...) If you use a t-connector to connect each side of the circuit to a compressor (that uses a SMALL pump and NO tank!) you can maintain high pressure, and the fact that the pump's cylinder is small compared to the other two cylinders means that (...) (27 years ago, 10-Aug-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: Pnuematics: e-switch and thoughts
|
|
(...) That link doesn't work anymore. Can anyone tell us how this construction worked? (any gears? Levers? Maybe a worm gear?) I might want to use the idea in a Mindstorms design. (by the way, I really liked the soda bottle tank idea and might try (...) (27 years ago, 10-Aug-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: new products (Remote Control)
|
|
The remote is really handy when checking your creations before you program them. I use mine all the time. Also fun to run little cars and other bots. Even used it to drive my 8448 Street Sensation about the house. Bob Fay rfay@we.mediaone.net The (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
|
| |
 | | RCX Firmware storage.
|
|
After a near heartattack with my TI-89 after upgrading it's flash ROM (I think it is flash rom, Flash Somethin, (URL) I have to ask myself what exactly does the RCX have to store the Fireware. After pulling all avaible power source to my TI-89, it (...) (27 years ago, 10-Aug-99, to lugnet.robotics)
|
| |
 | | Re: IR-Tower and PowerBook-G3 ?
|
|
(...) I use the IR tower with a Wallstreet regularly (NQC was developed on my PowerBook), and I haven't had any problems. Did you make sure that AppleTalk is either set for Ethernet or turned off completely? You also may want to disable other (...) (27 years ago, 11-Aug-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: NQC (Mac) and KeySpan card?
|
|
(...) Yes, but you need to know the name of the device driver, and this is usually pretty difficult to find. Serial ports use two separate drivers - one for input and one for output. Usually the names are something like this: ".xxxIn" and ".xxxOut" (...) (27 years ago, 11-Aug-99, to lugnet.robotics)
|
| |
 | | Re: RCX Firmware storage.
|
|
(...) microcontroller's on chip ROM. The other half (which gets downloaded) isn't really firmware. Its stored in SRAM that is powered from the main batteries. If you take out the batteries the firmware will be lost after a few minutes. If you want (...) (27 years ago, 11-Aug-99, to lugnet.robotics)
|