 | | Re: pneumatics & mindstorms?
|
|
(...) I built a compressor with the large pump with the spring removed. It worked but it was too slow . It took 3-4 minutes before enough pressure was available to open a big piston just once. The compressor had to be geared very slow to provide (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: legOS and Markus in Forbes
|
|
(...) This is BIG NEWS and GREAT exposure for Markus and friends!!! -- a major business magazine recognizing the pursuits and achievements of adult LEGO fanatics on the net to extend the RCX technology toward greater heights! In May, Forbes also had (...) (27 years ago, 27-Jul-99, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.legos, lugnet.general, lugnet.publish, lugnet.announce)
|
| |
 | | Re: Pneumatics and Mindstorm
|
|
> I have never tried to send an attachment to the group so > sorry if it does not work. It works fine, but please, don't do it. Just go open a XOOM.com membership ("It's free!"), stuff the image there, and give us the URL. (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
(...) Why is this? The further apart they are, the greater r*cos(theta) is going to be for any given theta. Seems like that would make for more turning resistance, not less. (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
(...) Because the wheel base length shrinks in relation to the turning radius. It is this distance that causes the friction. The further this point is from the imaginary circle that the treads describe, the more perpendicular friction there is. As (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: legOS and Markus in Forbes
|
|
(...) (I guess I should have posted, instead of going to lunch! ;-) But there *IS* a URL...they just didn't put http:// in front of it, so your browser may have missed it. They mentioned Markus' site ((URL) in that same paragraph. (They mention (...) (27 years ago, 27-Jul-99, to lugnet.robotics.rcx.legos, lugnet.loc.us.ca.sf)
|
| |
 | | Re: Need treads
|
|
(...) I recently posted a notice to the Robotics forum about the fact that KB Toys is selling the 8414 Mountain Rambler set for about $20 US, down from about $33. You can see a picture of this set at the following location: (URL) set includes a pair (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | RE: TIMER 0 is flakey
|
|
(...) Looks like I'd better test this again, and maybe release 1.06... Sorry. Cheers, Ralph Hempel - P.Eng ---...--- The train stops at the train station, The bus stops at the bus station, So why am I sitting at a work station? ---...--- Reply to: (...) (27 years ago, 27-Jul-99, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: Do the high resolution timers work?
|
|
(...) Yep, you've got the parameters backwards. Try FFFF 0 timer_set. Also, I'm not sure about numbers above 0x8000... I'm working on a TclTk interface for uploading firmware images to the RCX and for pbFORTH scripts. I ALMOST have the comment (...) (27 years ago, 27-Jul-99, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Re: Mechanical question
|
|
(...) I'll try to explain this with an ASCII picture, but I'm make no promises about the quality... Please use a fixed font (as you always should in newsgroups) Legend: #### - Lower part of the track (the part that touches the ground). OOOO - Inner (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|