To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *12861 (+10)
  Lego Scanner - DTM
 
Hi all. I have pics and info of my latest creation - A Lego Scanner (~25 dpi) I like to call DTM (Digital Terrain Modeller). To see it go to www.astolfo.com/lego and go to the Mindstorms section. CIAO (27 years ago, 26-Jul-99, to lugnet.robotics)
 
  Zapped Firmware
 
-Apparently I have twice erased my firmware by putting a heavy load on motors attached to the RCX. The batteries do not appear to be dead. Is this normal behavior? -JW Jonathan Woodward woodward@guesswork.com (URL) find your (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
 
  Re: Weak Motor
 
(...) It wouldnt be wise to directly connect your 12V supply to the Handy Board... even if it doesnt cause damage to your Handy Board, I dont think your motor will be able to draw sufficient current from the motor port to run properly. Rather, you (...) (27 years ago, 26-Jul-99, to lugnet.robotics.handyboard)
 
  Temperature Sensor
 
Does anyone know the exact characteristics of Lego's temperature sensor? It's easy enough to buy a thermistor and hook it up, but I'd like the temperature readings to be accurate. I've seen thermistors described by a resistance at 25 degrees C and a (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
 
  Interfacing handyboard with Basic Stamp2
 
Hello to everybody. I would like to ask if is possible to interface the handyboard with the basic stamp2 using not the RS232. Thanks beforehand. (27 years ago, 26-Jul-99, to lugnet.robotics.handyboard)
 
  Re: HB Serial line speed change
 
(...) I haven't looked at the schematics for the handyboard for a while, but if you use an E-series processor, then I think you can go up to 12MHz (3 MHz E-Clock). I'm not sure whether the rest of the Handyboard could take the increased speed, and (...) (27 years ago, 26-Jul-99, to lugnet.robotics.handyboard)
 
  Re: Best (disposable) battery for the RCX?
 
It's strange that you say alkaline batteries don't "seem to last very long at all". I've been using mine for over a month. You should probably qualify your statement by saying how many minutes or hours you've run the motors on those batteries. (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
 
  Re: Homing with the IR Tower
 
(...) All you need is to put a differential between the wheels. If those wheels need to have traction, all you have to do is to apply the force to the differential itself and the differential will distribute the traction for the two wheels like a (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
 
  Re: Best (disposable) battery for the RCX?
 
Well, I wouldn't really even use the batterires unless I was going to do some robot that had to be moving around. I would just use an AC Adapter for it. Simplistic and cost effective instead of blowing 6 batteries in a few short hours of using the (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
 
  Mechanical question
 
I've been puzzling over this one, and I still don't really understand it: Why can a bot with tank treads do a turn in place, while a bot with four wheels geared together so that the front and back wheels on each side always move together can not? My (...) (27 years ago, 26-Jul-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR