To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *12826 (+10)
  Re: Mindstorms Add-ons
 
(...) For sensors and Mindstorms-specific stuff, the Lego World Shop (URL) your best bet. Prices are decent and shipping time is about a week to the UK. The exception is if you need another motor, where your best bet is the ZNAP Hoversub (#3552), (...) (27 years ago, 23-Jul-99, to lugnet.robotics)
 
  HB Serial line speed change
 
Hi! I'm asking this again, since I've got no definitive answer: Is it possible to change the speed of the HB serial line to 19200? I need to communicate with a device which has a fix 19200 setting! Is it possible or can I forget the HB for this (...) (27 years ago, 23-Jul-99, to lugnet.robotics.handyboard)
 
  Re: HB Serial line speed change
 
To add to Martin's question, how can you change the baud rate used by IC 3.x? It's easy enough to alter the speed of the UART by setting the BAUD register or POKEing the relevant location in the pcode interpreter. Randy Sargent's code fragments can (...) (27 years ago, 23-Jul-99, to lugnet.robotics.handyboard)
 
  Adder-Subtractor w/Clutch?
 
-So, my Lego Ogre project is proceeding. ((URL) The current assembly I'm having problems with consists of two motors, one powering the left tread, one powering the right tread. The output from these motors is also being piped through an (...) (27 years ago, 23-Jul-99, to lugnet.robotics)
 
  Re: IC Problem
 
(...) I had to go RTFM for this one ;-) It says: 5.6 Arrays and Pointers IC supports one-dimensional arrays of characters, integers, long integers, and floating-point numbers. Pointers to data items and arrays are supported. It doesn't say that (...) (27 years ago, 23-Jul-99, to lugnet.robotics.handyboard)
 
  Re: NQC emulator?
 
The idea has cropped up from time to time, but nobody has written one yet. You probably don't want to simulate NQC code, but rather interpret the bytecodes emitted by the NQC compiler. These are just the bytecodes of the standard Lego firmware. (...) (27 years ago, 23-Jul-99, to lugnet.robotics.rcx.nqc)
 
  Re: problem with control speed using NQC
 
The Mindstorms RCX Code software does the exact same thing as the code you listed, the only caveat is I think RCX Code uses power settings from 1 to 8 while NQC uses 0 to 7. Both result in the same bytecodes for the RCX to interpret. // turn A on (...) (27 years ago, 23-Jul-99, to lugnet.robotics.rcx.nqc)
 
  something is wrong with my handyboard
 
when I turn on my handyboard, a row of black squares appears on the top line of the LCD screen. I have had friends check for shorts and I have redownloaded the pcode_hb.s19 programs on to the handyboard (as the FAQ part of the handyboard web page (...) (27 years ago, 23-Jul-99, to lugnet.robotics.handyboard)
 
  Interactive human-controlled bots
 
At a local toystore last night, they had a big setup of Rokenbok (a pseudo-LEGO-compatible construction toy system) with a bunch of radio- controlled dump-trucks, ramps, bridges, balls to move around, and so forth. OK, Rokenbok certainly leaves a (...) (27 years ago, 23-Jul-99, to lugnet.robotics)
 
  Re: something is wrong with my handyboard
 
Can you put the board in bootstrap mode? (...) (27 years ago, 23-Jul-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR