To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *11961 (+20)
  RE: Pitsco v. World Shop
 
(...) [...] (...) (URL) -Good stuff, in bulk. -JW Jonathan Woodward woodward@guesswork.com (URL) of packing material voids warranty." -Standard Acme Disclaimer -- Did you check the web site first?: (URL) (27 years ago, 8-Jun-99, to lugnet.robotics)
 
  Re: Digital Input Problems
 
(...) Sounds like the inputs are shorted together somehow. Check your soldering in this area for bridges. Best, Duncan (27 years ago, 8-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Motor Sensor
 
(...) The hardest part, assuming you could find a way to read both clockwise and counterclockwise rotations, is going to be converting velocity (which is effectively what the motor will tell you) into position, assuming that is what you wanted to (...) (27 years ago, 8-Jun-99, to lugnet.robotics)
 
  Re: How to make your own assembly code position independant
 
Marobi, Do not know much about IC and assembly code downloading. However, I have produced a system for programming the HandyBoard with Assembly/machine code. This system may help you. It can be downloaded from: (URL) (...) Charles Hacker Lecturer in (...) (27 years ago, 8-Jun-99, to lugnet.robotics.handyboard)
 
  arbitrary motor allocation
 
If I recall correctly, there was some discussion of a rewrite of the OS's motor code so that arbitrary motors could be assigned by the code without the need for a large case statement in user code. Has that happened? Is it happening? Can I help? (...) (27 years ago, 8-Jun-99, to lugnet.robotics.rcx.legos)
 
  Re: Motor Sensor
 
Dennis Clark <dlc@verinet.com> wrote in message news:FD0uAG.G9s@lugnet.com... (...) select (...) Actually the RCX reads voltage. In any of the passive modes it reads from 0 to 5V. There happens to be a pull up resistor (10K to 5V) internal to the (...) (27 years ago, 9-Jun-99, to lugnet.robotics)
 
  Re: Motor Sensor (fwd)
 
----- Forwarded message from Kekoa Proudfoot ----- From: kekoa@pixel.Stanford.EDU (Kekoa Proudfoot) Subject: Re: Motor Sensor Date: Tue, 8 Jun 1999 22:35:23 GMT The hardest part, assuming you could find a way to read both clockwise and (...) (27 years ago, 9-Jun-99, to lugnet.robotics)
 
  RE: Motor Sensor
 
I expect that Lego has designed the RCX so that hooking up an output port to an input port directly will not damage it. Kids will probably do that just for fun sooner or later. Hooking up a motor to an input port should therefore be safe, too, as it (...) (27 years ago, 9-Jun-99, to lugnet.robotics)
 
  RE: Motor Sensor (fwd)
 
----- Forwarded message from Tilman Sporkert ----- From: "Tilman Sporkert" <tilman@activesw.com> Subject: RE: Motor Sensor Date: Tue, 8 Jun 1999 17:47:52 -0700 Getting useful readings from that is another matter. As stated earlier, the RCX reads (...) (27 years ago, 9-Jun-99, to lugnet.robotics)
 
  Re: Motor Sensor (fwd)
 
Accually, you can determine the violcity via distance over time. KGB AgEnT #4 OUT -- Did you check the web site first?: (URL) (27 years ago, 9-Jun-99, to lugnet.robotics)
 
  RE: Motor Sensor (fwd)
 
(...) Yes, you get a reverse current, but the RCX won't be able to measure that. Anything below 0V will read the same as 0V (RAW = 0), and anything above +5V will read as 1023 in RAW mode. Tilman -- Did you check the web site first?: (URL) (27 years ago, 9-Jun-99, to lugnet.robotics)
 
  Re: Motor Sensor (fwd)
 
(...) Right, but one direction results in positive voltages, and the other results in negative voltages. And the RCX can only measure positive voltages. (...) It's actually not angular acceleration, it's angular velocity. -Kekoa (Sorry Jim, I (...) (27 years ago, 9-Jun-99, to lugnet.robotics)
 
  Re: arbitrary motor allocation
 
(...) Why does the code need a case statement? What interface are you looking for? void motor_dir(motor, dir) and motor_speed(motor, speed)? I missed the previous discussion. This is easy to implement, with no major changes to the code, just an (...) (27 years ago, 9-Jun-99, to lugnet.robotics.rcx.legos)
 
  RE: Motor Sensor
 
(...) in 100ms increments? Anything faster than 5 Hertz is not going to read accurately. Stuart -- Did you check the web site first?: (URL) (27 years ago, 9-Jun-99, to lugnet.robotics)
 
  Microsoft IntelliEye mouse - very good robot position tracker?
 
Product Description: "Microsoft IntelliEye technology employs a tiny chip with a sensor and digital signal processor (DSP). The sensor’s glowing red light captures “snapshots” of the work surface at a rate of 1,500 images per second. The DSP (...) (27 years ago, 9-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Robotic Vacuum Cleaner
 
(...) Funny just a few minutes before I read your mail I read a ad in the local newspaper about this nice robot (If you own a lawn that is). (URL) (Unfortunatley in swedish) There's even a solar powered version (This I think was the first version) (...) (27 years ago, 9-Jun-99, to lugnet.robotics)
 
  Re: Motor Sensor (fwd)
 
----- Forwarded message from Kekoa Proudfoot ----- Subject: Re: Motor Sensor (fwd) Date: Wed, 9 Jun 1999 01:56:23 GMT (...) It's actually not angular acceleration, it's angular velocity. ----- End of forwarded message from Kekoa Proudfoot ----- (...) (27 years ago, 9-Jun-99, to lugnet.robotics)
 
  RE: Motor Sensor (fwd)
 
----- Forwarded message from Tilman Sporkert ----- From: "Tilman Sporkert" <tilman@activesw.com> Subject: RE: Motor Sensor (fwd) Date: Tue, 8 Jun 1999 18:46:09 -0700 (...) Yes, you get a reverse current, but the RCX won't be able to measure that. (...) (27 years ago, 9-Jun-99, to lugnet.robotics)
 
  Re: Motor Sensor (fwd)
 
(...) No, it's actually not angular acceleration, it's angular velocity. Constant rotation = constant angular velocity = zero angular acceleration. The vector of angular velocity is parallel to the axis of rotation, and is constant throughout the (...) (27 years ago, 9-Jun-99, to lugnet.robotics)
 
  Identifying an RCX?
 
My RCX has a (presumably unique) serial number printed on the top. It would be nice if that, or some other unique identifier, was available from some command. Then when my robot drives out of range and a possibly different one drives back in, I (...) (27 years ago, 9-Jun-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR