 | | RE: Multitasker test script
|
|
(...) Post away! Two heads (too bad there only seem to be two of us :-( are usually better than one! Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) ---...--- Reply to: rhempel at bmts dot com ---...--- (28 years ago, 12-May-99, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Re: MC34064
|
|
please don't send attachments to the mailing list. a 200 K message sent out to 500 people is 100 megs of data. also some people have small mailbox quotas that can be filled up by just one big attachment. i realize 200K isn't huge, but it's still a (...) (28 years ago, 12-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Fishing for a tasty linkage/gearing/robotic building thread...
|
|
(...) I am working on a LEGO color copier machine. I've been fooling with it for a couple of months now (not so much due to difficulty as to lack of free time). Physically, my copier is basically an XY plotter with four interchangable colored pens. (...) (28 years ago, 12-May-99, to lugnet.robotics)
|
| |
 | | Re: Fishing for a tasty linkage/gearing/robotic building thread...
|
|
Michael, If you only need to make right angle changes of direction how about a design where the robot does not turn. You could have one set of axles for forward/backward with 1 motor driving both sides so you go straight. Then to change direction a (...) (28 years ago, 12-May-99, to lugnet.robotics)
|
| |
 | | Re: Fishing for a tasty linkage/gearing/robotic building thread...
|
|
I would try using one motor to drive and a ratchet on one of the wheels. Then when you go in reverse, you turn. Time the motor power setting and turn rate until you get a good 90 degree turn. The other way would be to use some kind of line (...) (28 years ago, 12-May-99, to lugnet.robotics)
|
| |
 | | Re: Fishing for a tasty linkage/gearing/robotic building thread...
|
|
(...) I was toying around with something like this. A foot like thing would come down, lift the whole vehicle up off the ground, then turn it right or left 90 degrees (maybe even a variable angle), and set it back down. It does look like a three (...) (28 years ago, 12-May-99, to lugnet.robotics)
|
| |
 | | Light sensor help??Newbie!!!
|
|
Hi All! I have a problem with the light sensor using the included software. (Don't groan all you advanced programmers, please ;-> ) But anyway, the manual states and I quote" trigger the stack when the FIRST of TWO consecutive readings falls outside (...) (28 years ago, 12-May-99, to lugnet.robotics)
|
| |
 | | Re: Fishing for a tasty linkage/gearing/robotic building thread...
|
|
(...) You could use a synchro-drive type of platform. This has been mentioned on here a few times before with varying levels of complexity. Since you only need 90 degree angles then you could probably get away with synchronizing the wheel direction (...) (28 years ago, 12-May-99, to lugnet.robotics)
|
| |
 | | Re: Fishing for a tasty linkage/gearing/robotic building thread...
|
|
(...) This is very close to what I was thinking. if you lowered a plate, lifted the bot and then rotated it and then rised the plate lowering the bot. With some clever mechanics you mifgt get the lifting and rotating done with one motor. I would (...) (28 years ago, 12-May-99, to lugnet.robotics)
|
| |
 | | Re: Multitasker test script
|
|
Here it is, it is working, but is waiting for IR_MODE_HI, STOP and a non-blocking EMIT. There is a light sensor on the centre connector pad. .dp displays proximity in the LCD as DEFCON.RawLight alternating with the average ambient raw light sensor (...) (28 years ago, 12-May-99, to lugnet.robotics.rcx.pbforth)
|