 | | no download mode
|
|
I spilled coffee on my handyboard this morning - it was powered off at the time. There was liquid across several pins on the 6811, though. I removed the 6811 and cleaned it up, then reinserted it. Now, both red&green LCDs come on when I turn it on. (...) (30 years ago, 23-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: no download mode
|
|
(...) Mine was doing what sounds like exactaly the same thing... Try replacing you MAX 232 chip if nothing else works, I blew mine out (god knows how) a while ago, and was acting like you said. Just a suggestion :) -Wes (30 years ago, 23-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Polaroid pinouts
|
|
Hi I've just received my Polaroid sonar stuff, but there's no documentation ! (of course Polaroid appear to have closed for Xmas.....) Does anyone have the pin assignments for the 6500 series Polaroid sonar module. The connector is roughly in the (...) (30 years ago, 23-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | (Polaroid Pinouts)
|
|
Scott, The J1 connector has the following pin assignments: pin 1 GND pin 4 INIT pin 9 V+ pin 6 OSC pin 7 ECHO pin 8 BINH pin 2 BLNK (30 years ago, 24-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Sorry, my E-mail address is realy: ameba@email.mcleod.net -thanx (30 years ago, 24-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | E-mail Address
|
|
My e-mail is going psycho. just to make sure, my email address is:: ameba@mcleod.net -thanx (30 years ago, 24-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Assembling the HandyBoard
|
|
Hello all: We got the handyboard assembly kit from Digital Micro Systems. We are putting it together now. Everything has gone well. Thanks, the instructions are really good. A couple of things have not worked quite right: 1. Couldn't find the 2.2M (...) (30 years ago, 25-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Assembling the HandyBoard
|
|
(...) You need that resistor to stabilize the crystal frequency. Try Radio Shack if it is missing from the kit. It doesn't have to be 1/8 watt, 1/4 or 1/2 watt is fine, just make sure it is 2.2 megaohm. (...) So far so good. (...) There is probably (...) (30 years ago, 26-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Assembling the HandyBoard
|
|
(...) I was getting similar behavior with my board. It wasn't clear to me that pins 2 and 3 in the serial cable from the PC to the interface board should be switched. Credit goes to Mike Ross for helping me figure this out. Once I switched these two (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Thanks, Fred
|
|
Fred, Thanks for giving us this great design. I appreciate it and I enjoyed building my Handy Board from a kit. I do have two corrections, though. No big deal, just typos. In the on-line assembly instructions, J15 is referred to as J14 at one point, (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
|