 | | Re: charger
|
| (...) In short, No. The charging cicuitry on the HB (especially the zap mode) is designed for a 500ma supply. People have had problems with 1 amp ones. Best, Duncan (28 years ago, 9-May-99, to lugnet.robotics.handyboard)
| | |  | | Re: Would-be hacker queries. / Re: Request for new list
|
| Hi again. Laurentino was so kind as to give me the definitions of the terms I mentioned. Is it generally agreed that an intelligent newby can ask for definitions of technical terms, as the discussion goes along? If so, I'll try to keep it (...) (28 years ago, 9-May-99, to lugnet.robotics)
| | |  | | Re: Would-be hacker queries. / Re: Request for new list
|
| Great, Eric! Great answers. Thanks for your help. In cooperation, I think we can compile an awesome programming FAQ. The robots are coming! I'm very excited by the future of robotics in the wake of developments including the RCX. I get the (...) (28 years ago, 10-May-99, to lugnet.robotics)
| | |  | | SHARP new product
|
| Hello everyone, Sharp recently release the new GP2D12 (General Purpose Distance Measuring Sensors). Which performs same as the GP2D02. The new product have only 3 pins - Vo, Gnd, and 5V. Vo is an analog output, which means you can use it on any (...) (28 years ago, 9-May-99, to lugnet.robotics.handyboard)
| | |  | | Re: charger
|
| (...) I'm relying on non-handyboard experience here, but I'm going to assume that's too much. One amp is a heavy load, and although there's a 5v regulator on the circuit, I'd guess that it's not rated for 1 amp (it may just run hot) and might not be (...) (28 years ago, 10-May-99, to lugnet.robotics.handyboard)
| | |  | | Measuring motors current
|
| Hi, I'm using for my base 12 v geared motors ,without load, each one drives less than 100 mA, but when stalled, the current grow to 500 mA, wich is to close to the 600 mA of L293 chips, i do not need more current, but i want to protect the L293 from (...) (28 years ago, 10-May-99, to lugnet.robotics.handyboard)
| | |  | | Re: charger
|
| Hi all: The problem with using a wall wart that is NOT 12 V @ 500 mA is this: most wall warts are _not_ regulated, and they have a fairly high internal impedance. If there is no load on a "12 V" unit, the output voltage will likely be at least 18 V, (...) (28 years ago, 10-May-99, to lugnet.robotics.handyboard)
| | |  | | Re: Ir transmission
|
| (...) I can't get EMIT to work, in NQC I do this: SendMessage(255); // Flash Sleep(3); ThisRaw = RAW_LIGHT; and the raw light sensor reading has big spikes for IR reflections. but: [ HEX ] FF EMIT 30 msWait RawLight LIGHT? does not, I think that (...) (28 years ago, 10-May-99, to lugnet.robotics.rcx.pbforth)
| | |  | | Re: RCX and Java
|
| (...) rotation (...) No, java was picked because the company did not wan't to use C++ as it had some bad experience with projects taking way too long to complete. It had used Visual basic (yieek) before but it tended to be slow and the code was not (...) (28 years ago, 10-May-99, to lugnet.robotics)
| | |  | | Re: charger
|
| the main reason this doesn't work is the 1a supply produces too high a voltage at the actual current being drawn, resulting too high a charge rate. technically, it will work in NORMAL charge mode, but you'll be charging the battery too fast, (...) (28 years ago, 10-May-99, to lugnet.robotics.handyboard)
| |