To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *11046 (+20)
  Pics of 1999 Mindstorms items
 
The press room at www.legomindstorms.com has some new pictures of the two new kits due out this year. From these pictures, it's clear that the "Scout" unit - in the Robotics Discovery Kit - is very similar to the RCX; it has only 2 inputs, and (...) (28 years ago, 24-Apr-99, to lugnet.robotics)
 
  Reading sensors at equal intervals.
 
Is it possible (with the standard firmware) to read the RCX sensors (actually, ideally, to run any old subroutine) at equal intervals, ie like every 100ms or something? (I assume it must be, otherwise you couldn't measure speed with the angle (...) (28 years ago, 24-Apr-99, to lugnet.robotics)
 
  Steer kit
 
I bought the Steering kit, 5295, and now can't envision how all of the pieces can be used. Does anyone have any examples they could share? -- Did you check the web site first?: (URL) (28 years ago, 24-Apr-99, to lugnet.robotics)
 
  Re: Steer kit
 
David Cuthill <lego-robotics@crynwr.com> wrote in message news:01BE8DCB.0A59FE...ome.com... (...) One of the models on this page shows some of those parts. Sorry that they are not closeup. (URL) (...) (28 years ago, 24-Apr-99, to lugnet.robotics)
 
  Re: IR test reports "Rubbish" when I run test.c
 
Test.c expects to see both short and long pulses of IR, and it tries to accept timings from any remote. It times the signals it receives and records the lengths of the shortest and longest pulse. It then uses the midpoint of these values as a (...) (28 years ago, 24-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Reading sensors at equal intervals.
 
(...) By standard firmware, I assume you mean using the byte codes ala NQC or something similar. If you only want semi-precise timing, you can use the wait opcode to delay for approximately 100 ms between sensor samples. If you want something more (...) (28 years ago, 25-Apr-99, to lugnet.robotics)
 
  Re: Reading sensors at equal intervals.
 
(...) I though that the four "Timer()" values read out in 100ms increments only. Is there a way to get a 1ms timer with NQC? thanks, DLC (28 years ago, 25-Apr-99, to lugnet.robotics)
 
  Rom sensor read routine
 
In writing some sensor code yesterday/today (it's 6 am), I passed over the ROM sensor code at 14c0. The documentation has been put in the usual place. The rotation code is pretty simple: the expected state machine, with split points between the four (...) (28 years ago, 25-Apr-99, to lugnet.robotics.rcx.legos)
 
  Re: Reading sensors at equal intervals.
 
(...) You are right, the timer values as seen by the firmware are in 1/10ths of a second. I lost myself in H8-land, which has a 1 ms timer that gets divided down before being seen by the firmware. -Kekoa (28 years ago, 25-Apr-99, to lugnet.robotics)
 
  Re: pneumatic switch control
 
Dennis Clark wrote in message ... (...) dropped (...) See demonstartion of the principle: (URL) pneumatic control from menu Eric Brok Visit LEGO ON MY MIND: (URL) Control section: (URL) section: (URL) (28 years ago, 26-Apr-99, to lugnet.robotics)
 
  Re: Pics of 1999 Mindstorms items
 
S. Crawshaw wrote in message ... (...) I offered an explanation for that in a previous post. May want to look it up. Eric Brok (28 years ago, 26-Apr-99, to lugnet.robotics)
 
  RcxCC Help!
 
i downloaded the RcxCC version 2.2 and extracted it with winzip. when i try to run the RcxCC.EXE, my system say "Exception EOleSysError in module RcxCC.EXE at 00053AF9. Class not registered" does anyone know what it is and what can i do?? thanks in (...) (28 years ago, 26-Apr-99, to lugnet.robotics.rcx.nqc)
 
  Re: RcxCC Help!
 
OH! i forgot i need to install the mindstorm software before i use RcxCC!! now it works, sorry guys. (...) (28 years ago, 26-Apr-99, to lugnet.robotics.rcx.nqc)
 
  Re: RcxCC Help!
 
William: Do you have the official Mindstorms software loaded that came with the RCX? Most of the 3rd party programs need the main program loaded inorder for their program to run properly. Hope this helps... Best Regards, Patrick McLean William Ng (...) (28 years ago, 26-Apr-99, to lugnet.robotics.rcx.nqc)
 
  CMOS CAMERA
 
Anynoe did connect a CMOS camera to Handy Board ? Is possible ? (28 years ago, 26-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Reading sensors at equal intervals.
 
(...) <snip> (...) That looks like a "no" then... How does the timing of tasks work? I seem to recall reading somewhere that the firmware executes the tasks in sequence - is there any timing element to this, or does it just do task 1, then (...) (28 years ago, 26-Apr-99, to lugnet.robotics)
 
  doc info
 
I am buliding my own handy board and I having difficulty downloading the "Assembling The Handy Board" file off the web site. Does anybody know any other way to obtain this document? Fred (28 years ago, 26-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Reading sensors at equal intervals.
 
(...) IIRC, it preferentially executes a single instruction received from the IR connection, otherwise takes the next instruction from the next task and executes that instead. (...) Probably. I don't think LegOS supports (what I'd call) a software (...) (28 years ago, 26-Apr-99, to lugnet.robotics)
 
  GCC/HC11
 
Just to let everyone know: I think I may have found a new compiler bug with the GCC/HC11 C-compiler. When I did this: c = d = serial_getchar(); My program didn't work correctly. If I did this instead: c = serial_getchar(); d = c; It worked fine. (...) (28 years ago, 26-Apr-99, to lugnet.robotics.handyboard)
 
  Please help me.
 
Hello all. I have just begun 68HC11 study. So, everyone has a question. 1. I want to know how to change hex file to motorola s19 file. 2. I want to know where it is free disassembler for 6811. Please help me!! Yoshi astronauts@mail.goo.ne.jp (28 years ago, 27-Apr-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR