 | | Re: pneumatic switch control
|
|
I just got my RIS as well as some pneumatic parts yesterday. The timing couldn't be worse as I'm in the middle of finals and can't spare much time for non-studying activities. However, your suggestion inspired me to take a study break and open up my (...) (28 years ago, 23-Apr-99, to lugnet.robotics)
|
| |
 | | RE: Electrolytic Capacitor Ratings [was Re: Choosing Parts?]
|
|
Sorry, no. The breakdown occurs purely from the dielectric material. Remember lightning? You don't all of a sudden see the clouds come crashing down to the ground and then have a discharge. (...) (28 years ago, 23-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: SoCal LegoLand
|
|
In article <199904222202.SAA232...navy.mil>, Ken Hornstein <kenh@cmf.nrl.navy.mil> writes (...) and in article <371FBB6F.236FDCF8@ghg.net>, John A. Donaldson <jdonaldson@ghg.net> writes (...) I'm 56 and drove _past_ Billund last September without (...) (28 years ago, 23-Apr-99, to lugnet.robotics)
|
| |
 | | Re: Using Lego IR outside of Lego
|
|
(...) If your laptop has one of the newer (1997) or later super-io chips as the controller for the IR, you may be able to get it to communicate with the tower. The trick is to setup the chip into SHARP IR mode (which transmits data at 38.4k on a (...) (28 years ago, 23-Apr-99, to lugnet.robotics)
|
| |
 | | Re: pneumatic switch control
|
|
At 05:13 AM 4/23/99 -0400, you wrote: <snip> (...) Awesome. It was easy to think of, but I'm not sure that I could have built it as well as you. I particularly like the cam mechanism that you developed, and the use of just one touch sensor. Very (...) (28 years ago, 23-Apr-99, to lugnet.robotics)
|
| |
 | | IR test reports "Rubbish" when I run test.c
|
|
When I try to get the values for my IR transmitter the test.c reports that it is a bad. It calls it 'rubbish' why would that be? -Peter (28 years ago, 23-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: handyboard clock speed
|
|
(...) From the data books for the 68HC11, if you have any version of the E-series (except for perhaps one, a low-power version?), you can run them at up to a 3MHz E-clock (12MHz crystal). I haven't looked at the rest of the handyboard schematic with (...) (28 years ago, 23-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: legOS Network Protocol
|
|
(...) given (...) lego (...) [ stuff about lego/native collisions ] (...) of a (...) on (...) I was wondering, since people are considering using tags in the LNP frame to signify local to local messages, could we not also use this to "label" non (...) (28 years ago, 23-Apr-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: handyboard clock speed
|
|
(...) yes, this is right. the fastest you can go with the 52-pin 6811s is 12 MHz crystal --> 3 MHz system clock (i'm pretty sure). so this is only 1.5x over the stock HB. so you've got the issue Curt pointed out with not only the downloader, but (...) (28 years ago, 23-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: handyboard clock speed
|
|
(...) Not going to mention the free Otto/Steven/Keith/Curt GCC-2.8.1 HC11 port? I'm hurt. ;-) Maybe you need to add my web & ftp pages to your free software page, now that I have a GCC Handyboard library available? GCC/HC11 patches are available (...) (28 years ago, 23-Apr-99, to lugnet.robotics.handyboard)
|