 | | Re: Sonar and Compass
|
|
(...) I have started working on an expansion board version of the compass code. I won't have it done before fall probably (unless is snows or something really bad). I am involved in another huge project right now. My thoughts are to have the compass (...) (28 years ago, 16-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: First 18 RCX IRPD kits are all gone
|
|
(...) OOps. As a few have pointed out to me, I didn't post anything to help others figure out what I was talking about... The full explanation on my RCX IRPD is located at:(URL) bonk on the RCX IRPD project for the full dope. sorry, DLC (28 years ago, 16-Apr-99, to lugnet.robotics)
|
| |
 | | Re: First 18 RCX IRPD kits are all gone
|
|
Dennis, I am interested. --Alan +---...--- | Alan G. Smith | ags@poboxes.com | (URL) (...) -- Did you check the web site first?: (URL) (28 years ago, 16-Apr-99, to lugnet.robotics)
|
| |
 | | Re: First 18 RCX IRPD kits are all gone
|
|
(...) I have got one and love it. It is simple to use and I like the fact that you get two eyes using only one sensor input. (See my previous post on the wall- follower I built using this IRPD.) Yes, if you make another run I will get one more set. (...) (28 years ago, 16-Apr-99, to lugnet.robotics)
|
| |
 | | Re: IRPD
|
|
In addition to checking for the width of the coke can, you could also have the robot drive its light sensor right up to the coke can, and check for what colour the can is. I'm assuming that coke cans are red, and that the walls aren't. I don't know (...) (28 years ago, 16-Apr-99, to lugnet.robotics)
|
| |
 | | Re: First 18 RCX IRPD kits are all gone
|
|
Please count me in as well. I am only sorry that I didn't get in on the first batch. -Phil (...) (28 years ago, 16-Apr-99, to lugnet.robotics)
|
| |
 | | Help on Microprocessor circuitry(4.1)
|
|
I'm having a lot of trouble with the first assembly of the handy board(4.1)...I installed all the parts, but the led does not light and I get zero voltage at GND and +5v...What could cause zero voltage accross the board??? I already switched D3(like (...) (28 years ago, 16-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re:Re: First 18 RCX IRPD kits are all gone
|
|
(...) [snip] (...) Yow! I give! I got at least 10 more people interested. I'll do it already. Those of you who sent me email, I'll send you my address. If anyone else is still interested, check my web page first to look at the assembly manual (URL) (...) (28 years ago, 16-Apr-99, to lugnet.robotics)
|
| |
 | | RE: First 18 RCX IRPD kits are all gone
|
|
I'll buy one as well. Sincerely, Michael Jones Peripheral Test Instruments, Inc. The Worlds Finest SCSI and FCAL Diagnostic Tools www.scsitools.com 303-763-7488 (...) -- Did you check the web site first?: (URL) (28 years ago, 16-Apr-99, to lugnet.robotics)
|
| |
 | | Please help
|
|
Hello all, I want to power some twelve volt gearmotors (The kind currently available from Acroname) with the H board without extensively (or permanently) modifiying the H board. My plan is to use some MOSFETS that have a low voltage gate threshold (...) (28 years ago, 16-Apr-99, to lugnet.robotics.handyboard)
|