To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10671 (+10)
  Power drain of the motors
 
Is there any way to measure the power drain of a running motor? The reason I ask is that I want to detect when the motor has stalled. I use nqc to program the brick. thanks -chris -- Did you check the web site first?: (URL) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Re: Power drain of the motors
 
(...) The CyberMaster can! ;-) Maybe there's some way you can connect one input to the motor output? Laurentino Martins [mailto:lau@mail.telepac.pt] [(URL) you check the web site first?: (URL) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  GCC/HC11 small patch
 
I contacted the original person who did the HC11 port to gcc (Otto Lind), and he pointed me to a patch for it. If you're using gcc-2.8.1 with the HC11 patches in it, you may want to try this: At line 502 of config/m6811/m6811.c, change from: { (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Increasing current output to motors on HandyBoard
 
Haven't actually tried it, but I was thinking of the same sort of thing. Use a FET for PWM and a DPDT relay for direction. practically speaking, if you only switched the relay when the FET was off, no power transition, etc.... If your 'bot moves (...) (28 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Increasing current output to motors on HandyBoard
 
Howdy, My original suggestion was to use *solid state* relays. They don't have any contacts. I use them plugged right into my Rug Warrior board at the motor output ports (would work the same on my Handy Board, but I have it on a smaller base, and (...) (28 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Increasing current output to motors on HandyBoard
 
So that's like $28 for the H excluding the protecting circuitry? How much did this setup cost for both motors? ---...--- ericson mar Robotics Consultant mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the (...) (28 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Quick troubleshooting help please!!!!
 
I would also check the circuit traces. Clip an ohm meter to the battery ground and check all the ground points, then do the same for +battery. Take a magnifying glass to the traces you can see. Look for places where the smoke got out. Once the (...) (28 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Increasing current output to motors on HandyBoard
 
Total cost for both, $56.00. Smaller ones are cheaper. Again, the advantage is convenience, not cost. These pulg right into the motor driver output ports on either the Handy Board or the Rug Warrior with the L293D left in place, and take no other (...) (28 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
 
  multitasking
 
I have a simple question regarding multitasking. I am using two subroutine in a multitasking. start_process(ir()); start_process(detect()); Both subroutine should run for 5 ms(default). Consider an example that the subroutine detect() require more (...) (28 years ago, 11-Apr-99, to lugnet.robotics.handyboard)
 
  Non-Lego mechanics reference / New Ideas?
 
Hi all, Has anyone come across any good basic mechanical reference resources? I have found that patent searches are a tad more complex than what I am looking for. I would be interested in hearing about non-Lego reference sites (or books!!)that cover (...) (28 years ago, 11-Apr-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR