To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10591 (+10)
  New Robotics on my wepsite...
 
Reciently I aquired an web cam and I couldn't resist making an attempt at making a webcam robot. This is the 2nd generation of the webcam robot. 1st generation never nade it into final assembly. Next is adding the RCX after I get extensions for the (...) (28 years ago, 6-Apr-99, to lugnet.robotics)
 
  Re: gcc build instructions for linux
 
(...) I got the same message, and your reasoning about the content of the message sounds AOK by me. But then I did a make install, and that crudded out on me, with the message In file included from ../../../egcs-1.1.2/...com.c:198: (...) (28 years ago, 6-Apr-99, to lugnet.robotics.rcx.legos)
 
  Re: gcc build instructions for linux
 
(...) I did not have this problem. Sounds like Fortran. Did you 'make LANGUAGES="c c++"' or just 'make'? The latter makes the Fortran stuff, too. Remember that if you specify LANGUAGES when building, you should specify the same value when (...) (28 years ago, 6-Apr-99, to lugnet.robotics.rcx.legos)
 
  Need info PLEASE
 
Hi, I have looked around on the mailing list and have not found anything that will answer this question.... I have an expansion board and want to use a 12v 2amp source for my motors. The hack listed in the FAQ is only for use on a handy board only, (...) (28 years ago, 6-Apr-99, to lugnet.robotics.handyboard)
 
  Hack for gearmotors sold by Acroname
 
Hi, The SOHO gear motors sold by Acroname have a high gear ratio and are too slow for what I needed (189:1 or something). The front gear cover is removable with two screws and one on the gears (there are 4 metal gears in addition to the small (...) (28 years ago, 6-Apr-99, to lugnet.robotics.handyboard)
 
  Re: gcc build instructions for linux
 
I got everything to build using egcs 1.1.2, but I am having problems with the tm-and-ir demo (after modifying it for the new execi syntax) which make me think maybe egcs is not generating correct code. I used the build instructions at (URL) did use (...) (28 years ago, 7-Apr-99, to lugnet.robotics.rcx.legos)
 
  Re: gcc build instructions for linux
 
This site is quite useful: (URL) found it via ftp.cygnus.com/pub/crossgcc. I hope it helps you out. Cheers, Vic (...) LANGUAGES="c (...) that (...) (28 years ago, 7-Apr-99, to lugnet.robotics.rcx.legos)
 
  Re: gcc build instructions for linux
 
(...) The helpful folks on the crossgcc mailing list told me that this error indicates that no libstdc was found, so no binary could be generated for the target (not host) platform. Since legOS provides a replacement library, there is no problem (...) (28 years ago, 7-Apr-99, to lugnet.robotics.rcx.legos)
 
  Lego #5391 as a project box
 
Those of you out there making my RCX IRPD kit may want to look at the Lego S@H #5391 9V battery box as an enclosure. I just got one and chopped off the "on button" side so that I was only using the last 5 bumps worth of the box. The IRPD assembly (...) (28 years ago, 7-Apr-99, to lugnet.robotics)
 
  1. Use of sony-ir functions in program; 2. smooth PWM
 
Hi everybody! My first question is about using the sony-ir functions in a program: After loading sony-ir.icb and executing "sony_init(1)" at the IC prompt, I can successfully retrieve signals from my sony remote control via the function (...) (28 years ago, 7-Apr-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR