To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10496 (+10)
  Re: Help needed!
 
I had a similar problem and had to try a different serial port. I have a serial mouse and the board will only work properly in com 1. If I try com 2, I get similar problems to yours keith (...) (28 years ago, 31-Mar-99, to lugnet.robotics.handyboard)
 
  Re: NQC tutorial available
 
(...) I think Mark is waiting for me to release NQC 1.3 - which is where SetWatch() gets added. In the meantime, you can define it yourself within your source code... #define SetWatch(h, m) asm { 0x22, (h), (m) } Dave (28 years ago, 31-Mar-99, to lugnet.robotics.rcx.nqc, lugnet.robotics)
 
  Re: NQC tutorial available
 
(...) "if (Random(100) == 0)" used to be a compiler error, but version 1.2 of NQC is smart enough to generate a temporary variable to hold the random number. A trickier problem is Sleep(). Sleep(Random(100)) parses just fine. Since Sleep() is just a (...) (28 years ago, 31-Mar-99, to lugnet.robotics.rcx.nqc, lugnet.robotics)
 
  Re: Help needed!
 
(...) DOING! Yeah, now that you mention it, I had the same problem when I got my HB. Took me about a week before I got around to trying COM1. That fixed it, so I left it that way and forgot about it long ago. At the time, no one on the list had any (...) (28 years ago, 31-Mar-99, to lugnet.robotics.handyboard)
 
  Re: new products
 
(...) messages. (...) *ONLY* 1, 2 and 3? This would make sense if you could control three motors with three buttons, but you'll need two directions AND stop for comfortable control of each motor. (or one message to turn motor on/off, second message (...) (28 years ago, 31-Mar-99, to lugnet.robotics)
 
  RE: Lego Motors
 
# From: antony@wellic.remove.this.demo # Sent: 30 March 1999 12:20 # To: lego-robotics@crynwr.com # Subject: Lego Motors # ---...--- # Does anyone know what RPM then standard Mindstorm motor does # at full power. I've have just purchased a ZNAP kit (...) (28 years ago, 31-Mar-99, to lugnet.robotics)
 
  Re: Lego Motors
 
Thanks for the info. I'll take a look at those links later (after work). The motor looks identical on the outside to the Mindstorm motors. Thanks again, Antony. (28 years ago, 31-Mar-99, to lugnet.robotics)
 
  Re: New Products
 
(...) can (...) messages. _Only_ 1 through 3? Cripes, what a gyp. ...Though, on the other hand, it does make the creation of an RCX-to-RCX protocol easier, since there are only a few messages that should be considered suspect. (I'm tentatively (...) (28 years ago, 31-Mar-99, to lugnet.robotics)
 
  Re: new products
 
(...) Maybe we can communicate with RCX via Morse code? :-) There are also five buttons to let you start any of the five stored programs. With the non-lego firmware, maybe we can use these five buttons for additional messages. Right now, for me the (...) (28 years ago, 31-Mar-99, to lugnet.robotics)
 
  Re: Help needed!
 
If you're having problems getting your HB to work on one serial port but it works on another, you might want to check for IRQ conflicts. By default, Com1 and Com3 both are assigned IRQ3, and Com2 & Com4 are both assigned IRQ4. So if you have a modem (...) (28 years ago, 31-Mar-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR