 | | Polarity Switch = Pressure Switch
|
|
Hi All, Just got my first Technic Polarity Switch and quickly put together a Pressure Switch for Pneumatics. Check out: (URL) and let me know what you think... Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
(...) It is a heck of a lot of complexity for a little added linearity. If you look at the plots on my general purpose interface section; the simple resistor interface is pretty linear. I think most of the nonlinearity in the powered version is due (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | RE: FORTH editor/IDE
|
|
(...) I'm not in the process of writing an IDE, but I'm not sure you need one either. (...) I'm going to make the pbFORTH a bit more user friendly shortly, by adding a MARKER word that essentially clears out all of your own definitions. (...) The (...) (28 years ago, 25-Mar-99, to lugnet.robotics.rcx.pbforth)
|
| |
 | | multi-device output controller
|
|
I've been considering various ways to control more than three output devices with only the three ports and came up with the following idea. I don't have the electrical design knowledge to implement, so if this idea sounds good, I'd like to (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Sharp GP2D02
|
|
I purchased two Sharp GP2D02 infrared sensors from Acroname and downloaded their interface to a Handy Board and Barry Brouilette's interface to the Handy Board. I was wondering which any of you have used and why so I can select one to use on in my (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: HB Memory
|
|
Stef, The HB comes with a 32K ram chip addressed at $8000 and above. A fair amount of this space is taken up with the Pcode interpreter if you run Interactive C, but there is still lots of room left for programs. Good luck, Gary Livick (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Help with pointers
|
|
(...) When you do pointer arithmatic, you work in increments of what the pointer points to. So if you have a pointer to an int, as in the above example, when you add one to it, you actually make it point to the next int, not the next byte or word. (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
I have not tried pneumatics yet. I know where I will look when I try them out. This is another neat clean working device. Nice work! Bob Fay rfay@we.mediaone.net The Shop (URL) Hempel <rhempel@bmts.com> wrote in message (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Robot Mapping
|
|
Hello, I am working on an autonomous mobile robot. Which has a sonar and infared sensor incorporated into it. Right now it can avoid objects, by sensing it and backing up and turning. I want my robot to take the information from the sensors and map (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
(...) Heck, I'd love to try some pneumatics, but you can't get a storage tank anywhere these days can you? All of the cool Technic kits are discontinued, no subs, (and while I'm whining) no shuttles, no tracked vehicles, only Throwbots and (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | RE: Sharp GP2D02
|
|
Scott, The reason I wrote mine the way I did was so that I could avoid disabling interrupts for long periods of time. If you don't care about timer interrupts or things like wheel encoders, either program should work fine. My program uses digital 15 (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Robot Mapping
|
|
I would also like to know about this. please cc any info to me too. =) chen (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
(...) 8462 comes with two of them, and is available from Lego S@H. I'd like to see reissues of the construction vehicles as well. alex -- Did you check the web site first?: (URL) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Help with pointers
|
|
(...) Actually, in 'normal C', to be completely correct you would cast the pointer conversion to show that you really knew what you were doing, like this: p = (char *) &x; Unfortunately, neither the free ware IC nor IC 3.2 support this. Here is (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: How do you convert light sensor data to bmp image
|
|
Alex: Downloaded the netphm files from your site. Your right, it was alot easier. Now all I have to do is build my scanner. Thank you for your help Patrick McLean :) Alex Wetmore wrote in message <922292440.681002@phred.org>... (...) image. (...) (28 years ago, 26-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | RE: Robot Mapping
|
|
Check this reference out: "Autonomous Agent Map Construction in Unknown Enclosed Environments", Keith L. Doty and Steven L. Seed, Machine Intelligence Lab, DEE, University of Florida, Gainesville, FL and Chapter 10 of: "Sensors for Mobile Robots, (...) (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Robot Mapping
|
|
(...) I've been thinking about this too. The problem as I see it is that without some shaft encoders on the wheels, your robot doesn't really know how far it's moved, and therefore where it is in the map. If you power on the forward motor for 2 (...) (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | [Fwd: Robot Mapping]
|
|
-- ___...___ Jonathan Pennington -Anthropologist/Geologist -Linux User and Advocate -Bart Simpson Sympathizer Email at jwp(at)awod.com ___...___ (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: [Fwd: Robot Mapping]
|
|
(...) Heck, that sounds pretty easy. As long as you know where you start from and you use a cartesian or polar form of V=vsub0 + a*t integrated over time, and you are either working in a vacuum or at such low velocities that c sub d is negligible, (...) (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
Dennis, Thanks for your encouragement. The angle sensor connected straight to the RCX is non-linear because it is in series with another resistor located inside the RCX. During a sense operation, the RCX drives the sensor input from a 10K resistor (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|