 | | Battery voltage available within NQC?
|
|
Last night I went out and bought six C cell nicads and wired them up as a power supply for my robot. What I'm wondering is this: is there some way to programmatically obtain the battery voltage, so I could make a decision based on a voltage (...) (28 years ago, 11-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Ultimate Starter Sets / Add-Ons for Mindstorm? Reprise
|
|
Mindstrom fans seem to go through a lot of grief finding or ordering just the right set of parts. I recently read a memo on the 'net lamenting some of the shortcomings of the Lego system: it is difficult to build certain structures, things must fit (...) (28 years ago, 12-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Battery voltage available within NQC?
|
|
(...) There's a bytecode (0x30) that instructs the RCX to send the battery voltage as a response over the IR. That's what NQC and Mindstorms use to read the battery voltage. I don't think this opcode has any effect within a program, or at best it (...) (28 years ago, 12-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Looking for Mac prog environment
|
|
(...) (URL) reply to: dbaum at enteract dot com (28 years ago, 12-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Battery voltage available within NQC?
|
|
(...) If you REALLY wanted to do this, you could use the bytecode to broadcast the battery information to the IR tower and have a service running on the PC which would recieve the battery message and then send an appropriate message back to the RCX. (...) (28 years ago, 12-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: More outputs, thinking outside of the box...
|
|
To get more electrical about it, how about making a voltage gate for the third output, that according to what voltage you set the third output to (between 1 to 9 volts), it switches on different sets of motors? Also, polarity changes could trigger (...) (28 years ago, 12-Mar-99, to lugnet.robotics)
|
| |
 | | Anybody have Peter Pletcher's TclRCX??
|
|
Laurent is very busy with his new child and hasn't made any progress on TclRCX and he never got together with Peter Pletcher. Peter Pletcher's web site is no longer online. I tried sending email to Peter, but have gotten no response. Does anybody (...) (28 years ago, 12-Mar-99, to lugnet.robotics)
|
| |
 | | Servo Expansion Board
|
|
Hi all, I have the Handy Board running fairly well, although I havn't tested ports, etc. Question. I have the expansion board, and when I try to run the init_servo (not exact) command, the board locks up. Anyone see this problem before? Thank you, (...) (28 years ago, 12-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Sensors
|
|
hi i'm trying to find a cheap and reliable infra-red digital sensor with a sensing range of around 0-30cm. does anyone have any recommendations? are there any online stores that sell a wide variety of such sensors? btw, the sharp GP2D05/02 sensors (...) (28 years ago, 12-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Polarity switch Question
|
|
Does anybody know if the polarity switch has a neutral center position? In other words, does the switch go: forward<->off<-->reverse Please share with the group... Cheers, Ralph Hempel - P.Eng ---...--- A picture is worth a thousand words, but very (...) (28 years ago, 12-Mar-99, to lugnet.robotics)
|