To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10136 (+10)
  Re: Sensor readings on the RCX display
 
You can also force it to run the output. Press and hold view while its pointing to a output, and then the Pgrm and Run buttons work to run it forwards and backwards. Its a bit of a pain to use, but nice when prototyping new mechanical creations. (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  San Jose event?
 
CGDC starts in a few days, but I haven't seen any updates on the San Jose lego robot event. Any news on where/when this is happening? -Allen (28 years ago, 11-Mar-99, to lugnet.robotics.events.robot-arena)
 
  Re: More outputs, thinking outside of the box...
 
(...) Often you don't need continuous motion, eg. robot arm, and you can keep to a limit. If you use another bump switch to tell the RCX that the motor shouldn't turn any more you can stop the action before you get to the second bump switch that (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Re: Bowing out of Joel's challenge!
 
Here is a rudimentary page with some pics of what I had. Important points to note: - This bot was designed to deal with empty cans only - Last design had 3 motors - but I was planning to eliminate one (hopefully) - I am an inexperienced hacker when (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Re: More outputs, thinking outside of the box...
 
Dennis - Check out my solution using small relays at: www.truepicture.com --- John. (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Battery voltage available within NQC?
 
Last night I went out and bought six C cell nicads and wired them up as a power supply for my robot. What I'm wondering is this: is there some way to programmatically obtain the battery voltage, so I could make a decision based on a voltage (...) (28 years ago, 11-Mar-99, to lugnet.robotics.rcx.nqc)
 
  Re: Ultimate Starter Sets / Add-Ons for Mindstorm? Reprise
 
Mindstrom fans seem to go through a lot of grief finding or ordering just the right set of parts. I recently read a memo on the 'net lamenting some of the shortcomings of the Lego system: it is difficult to build certain structures, things must fit (...) (28 years ago, 12-Mar-99, to lugnet.robotics)
 
  Re: Battery voltage available within NQC?
 
(...) There's a bytecode (0x30) that instructs the RCX to send the battery voltage as a response over the IR. That's what NQC and Mindstorms use to read the battery voltage. I don't think this opcode has any effect within a program, or at best it (...) (28 years ago, 12-Mar-99, to lugnet.robotics.rcx.nqc)
 
  Re: Looking for Mac prog environment
 
(...) (URL) reply to: dbaum at enteract dot com (28 years ago, 12-Mar-99, to lugnet.robotics)
 
  Re: Battery voltage available within NQC?
 
(...) If you REALLY wanted to do this, you could use the bytecode to broadcast the battery information to the IR tower and have a service running on the PC which would recieve the battery message and then send an appropriate message back to the RCX. (...) (28 years ago, 12-Mar-99, to lugnet.robotics.rcx.nqc)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR