 | | Re: Self Supporting Pod Racers —Terry Keller
|
| | | (...) What would happen if you added more of the flex tubes? Two more tubes, properly fastened, might give enough rigidity to hold up the 'cabin'. -- Terry K -- (25 years ago, 6-Jun-99, to lugnet.loc.us.ca.sf, lugnet.starwars)
|
| | | |
| | | | | Re: Self Supporting Pod Racers —Kevin Hutzol
|
| | | | | Terry K wrote in message <3759bdce.4028094@lu...et.com>... (...) the (...) One of the pod racers im working on has 4 of the flex tubes(the blue ones from the gungan sub), since im doing a non-standard(ie its 2 'engine' pods oriented horizontally), (...) (25 years ago, 6-Jun-99, to lugnet.loc.us.ca.sf, lugnet.starwars)
|
| | | | | |
| | | | | | | Re: Self Supporting Pod Racers —Jonathan Little
|
| | | | | | (...) I was thinking about that whole pod racer design. I mean, as far as the tan supports . . . if you were going to set up the pod race in some sort of desert diorama set up, they'd work great. They would probably blend right in. As far as just (...) (25 years ago, 6-Jun-99, to lugnet.loc.us.ca.sf, lugnet.starwars)
|
| | | | | | |
| | | | | | | | Re: Self Supporting Pod Racers —Steve Bliss
|
| | | | | | (...) I think the transparent plastic is somewhat more brittle than opaque plastic (and more expensive to produce). These aren't a problem with the STAPs, because there isn't much weight (or plastic) involved. The long plates on the pod racers might (...) (25 years ago, 7-Jun-99, to lugnet.starwars)
|
| | | | | | |
| | | | | Re: Self Supporting Pod Racers —Steve Bliss
|
| | | | [lugnet.loc.us.ca.sf snipped] (...) Or run wires through the flex tubes? The attachment points would need to be modified (those 1x1 clips won't hold), but the pod should be OK. Anyone got a good design for crossing the streams in a four-engine pod (...) (25 years ago, 7-Jun-99, to lugnet.starwars)
|
| | | | |
| | | | | | Re: Self Supporting Pod Racers —Charles Seyferth
|
| | | | | (...) Wow! Thanks for the idea. Since I seem to have wire laying around (I make chainmaille), I checked, and 16 gauge wire fits pretty darn well. A little weak, but 4 tubes just might work. Looking for something with a little more grip? Use the 1x1 (...) (25 years ago, 8-Jun-99, to lugnet.starwars)
|
| | | | | |
| | | | | | | Re: Self Supporting Pod Racers —Kevin Bane
|
| | | | | | Charles Seyferth <feanor23x@geocities.com> wrote in message news:375C76CE.D25882...ies.com... (...) There was one in the movie, and in SW:E1 Racer. Details to follow for those who STILL have not seen the movie and don't want it spoiled (I think (...) (25 years ago, 8-Jun-99, to lugnet.starwars)
|
| | | | | | |
| | | | | | | | Re: Self Supporting Pod Racers —Eric Joslin
|
| | | | | | (...) His name is Ben Quadrinaros, which might make it slightly easier to find shots of his Pod for reference material. eric (25 years ago, 8-Jun-99, to lugnet.starwars)
|
| | | | | | |
| | | | | | Re: Self Supporting Pod Racers —Sonny Sidhu
|
| | | | (...) WARNING: THESE INSTRUCTIONS REQUIRE COLD, HEARTLESS MUTATION OF UNEXPECTING AND INNOCENT LEGO PIECES. YOU HAVE BEEN WARNED. To make Quadrinaros' Pod, I used two standard energy beams from Anakin's Podracer. Attach them in an X, then tie clear (...) (25 years ago, 23-Jun-99, to lugnet.starwars)
|
| | | | |
