 | | Re: Defining the "term" BI
|
|
(...) I know. I was just teasing you about the book thing, because we *are* both in the same boat. Notice I immediatly followed with the list. Kevin (...) (21 years ago, 18-Sep-03, to lugnet.inst, lugnet.cad, FTX)
|
| |
| | Re: Defining the "term" BI
|
|
'snip' (...) I'm in the same boat as you on this issue of "book topics". I'm still wrtiting tutorials on subjects that I already helped cover in a book with Tim but that does the general public no good, unless they buy the book. However as the LDraw (...) (21 years ago, 17-Sep-03, to lugnet.inst, lugnet.cad, FTX)
|
| |
| | Re: Defining the "term" BI
|
|
Overview Model - the entire design being described by the building instructions. Building steps - the sequence of steps where parts are added to assemble the entire model. Sub-model - portions of the model that are described as their own set of (...) (21 years ago, 17-Sep-03, to lugnet.inst, lugnet.cad)
|
| |
| | Re: Defining the "term" BI
|
|
(...) I think I've already written a book that does this, which you haven't read :^) If you had you wouldn't have posted the original post that got all this going! Sure I'll add definitions for all the terms I use. (...) (21 years ago, 17-Sep-03, to lugnet.inst, lugnet.cad, FTX)
|
| |
| | Re: Defining the "term" BI
|
|
(...) I don't have any comments about it at the moment, but being that you have authored the 1st BI term page. =) I think we should used your page as our foundation. Perhaps you can "volunteer" again =) and write definitions for each of the terms. I (...) (21 years ago, 16-Sep-03, to lugnet.inst, lugnet.cad, FTX)
|
| |
| | Re: Defining the "term" BI
|
|
Ahui, Do you have any feedback on the below? Suggestions for specific names? Names for classes of images, etc? This post was to help you understand all the layers of stuff, so we could decide on good names and then all use the same dictionary. I'm (...) (21 years ago, 16-Sep-03, to lugnet.inst, lugnet.cad)
|
| |
| | Re: Defining the "term" BI
|
|
(...) Thanks Orion. Kevin (21 years ago, 15-Sep-03, to lugnet.inst, lugnet.cad)
|
| |
| | Re: Defining the "term" BI
|
|
(...) No, you posted it as FTX, I posted it plain text. The defualt for a given post is based on whether or not the parent message was FTX or not. In this case the parent post was FTX and you forgot to switch back to plain text causing your table to (...) (21 years ago, 14-Sep-03, to lugnet.inst, lugnet.cad)
|
| |
| | Re: Building Instruction Theory Article on BI Portal
|
|
"snip" (...) Yup, when I was writing the article I was thinking only of small to medium size models. Yoda is a scupltor and as such falls into a totally different catagory as the BIs are usually in a top-down view and the piece count is out the (...) (21 years ago, 14-Sep-03, to lugnet.inst, lugnet.cad, lugnet.general, lugnet.publish, FTX)
|
| |
| | Re: Defining the "term" BI
|
|
(...) I thought that ftx was optional. Why did you repost it as ftx? Kevin (21 years ago, 14-Sep-03, to lugnet.inst, lugnet.cad)
|
