 | | Re: Low Corner Slopes in Roof Parts Packs? —Jasper Janssen
|
| | | (...) Maybe they were old parts packs? I have one or two roof parts packs from before my Dark Ages, and I happen to have 8 or so, I think, 3 * 3 low corner slopes (in red). Not the reverse slopes, unfortunately :) Jasper (26 years ago, 19-Feb-99, to lugnet.general)
|
| | | |
| | | | | Re: Low Corner Slopes in Roof Parts Packs? —Gary R. Istok
|
| | | | (...) It's too bad that TLG doesn't make a 1x2 low slope (half pyramid) roof peak piece that would be used in conjunction with these low sloped corner bricks, like they do with the regular sloped bricks. Is that a possibility, or would there (...) (26 years ago, 22-Feb-99, to lugnet.general)
|
| | | | |
| | | | | | Re: Low Corner Slopes in Roof Parts Packs? —Jasper Janssen
|
| | | | On Mon, 22 Feb 1999 16:57:49 GMT, Gary Istok <gistok@umich.edu> wrote: <3*3 low slopes> (...) Good question... looking at my 2*4 low slope peaks, I have a feeling you may indeed be right about too little clearance :( You could use regular (medium (...) (26 years ago, 24-Feb-99, to lugnet.general)
|
| | | | |
| | | | | | Re: Low Corner Slopes in Roof Parts Packs? —James Brown
|
| | | | | (...) Hmm - It *should* be possible - unless I'm horribly mistaken (won't know for sure until I get home and do some comparisons), the area for a single stud on a pyramid roof peak should be the same as the area for a stud in the "corner" of a (...) (26 years ago, 24-Feb-99, to lugnet.general)
|
| | | | | |
| | | | | | Re: Low Corner Slopes in Roof Parts Packs? —Gary R. Istok
|
| | | | | (...) James, if you want a low-slope gable connector, then I'd want (most assuredly Rob Farver too) a low-slope INSIDE CORNER 3x3 brick, which also doesn't exist, because that is the piece that would give a low-slope gable connector a reason to (...) (26 years ago, 24-Feb-99, to lugnet.general)
|
| | | | | |
| | | | | | | Re: Low Corner Slopes in Roof Parts Packs? —Mark Koesel
|
| | | | | | | (...) It was always my understanding that the reason that roof pieces have a lip (i.e. the small vertical edge before the slope starts) was to provide a standard way, independent of slope angle, to keep the interior side of the slope from "crashing (...) (26 years ago, 24-Feb-99, to lugnet.general)
|
| | | | | | | |
| | | | | | | Re: Low Corner Slopes in Roof Parts Packs? —James Brown
|
| | | | | | (...) ^^^...^^^ (...) Rob (...) because (...) exist (...) Yup, I said that first, I just neglected to use accepted terminology :) I'm not sure that the concave (or inside corner, if you prefer) would give enough area to attach to a stud at the (...) (26 years ago, 24-Feb-99, to lugnet.general)
|
| | | | | | |
| | | | | | | | Re: Low Corner Slopes in Roof Parts Packs? —Robert Farver
|
| | | | | | (...) by adding a 1x3 slope to each side) it would increase attachable area, and stabilize the piece. This could also be done with the medium slope (increase to 3x3 with 1x2 slope area added to each side.) Of course, If they went and did all of the (...) (26 years ago, 24-Feb-99, to lugnet.general)
|
| | | | | | |
| | | | | | | | Steep Corner Slopes. —Gary R. Istok
|
| | | | | | | Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Now that we've analyzed the Low Corner Slopes, how about Steep Corner Slopes. Granted Steep Slopes don't come in Service Packs (too bad), and are therefore much much scarcer (...) (26 years ago, 25-Feb-99, to lugnet.general)
|
| | | | | | | |
| | | | | | | | Re: Steep Corner Slopes. —James Brown
|
| | | | | | (...) Yup! I was/am working on a keep that has one side going down into water, and the steep slopes work great as a flared base, except that it looks kinda funny where it meets in the corner. :-( How am I ever going to realize (one of) my dreams - (...) (26 years ago, 25-Feb-99, to lugnet.general)
|
| | | | | | |
| | | | | | | | Re: Steep Corner Slopes. —Jasper Janssen
|
| | | | | | (...) De Haar? The Dutch castle? Wow.. You must be the first non-Dutch person I've heard of that knows it exists... Jasper (26 years ago, 26-Feb-99, to lugnet.general)
|
| | | | | | |
| | | | | | Re: Low Corner Slopes in Roof Parts Packs? —Larry Pieniazek
|
| | | | <36D449DD.58F405FA@umich.edu> <F7oAsz.C6z@lugnet.com> Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit (...) I'll just use logic. Consider the convex... if it works, then the concave has to as well, as the edges must be (...) (26 years ago, 24-Feb-99, to lugnet.general)
|
| | | | |
