 | | Solution concerning MLCAD colors (was Re: Question about MLCAD colors)
|
|
Good Evening. I am writing to give my own suggestion about colors in MLCAD, based on pre-existing colors in LDraw. While some of the colors [when converting LDraw usage to MLCAD usage] turned out pretty well, others appeared so shockingly different, (...) (25 years ago, 23-Apr-01, to lugnet.cad.mlcad)
|
| |
| | Re: 2x3 trapezoid
|
|
(...) Thank you both very much, I must be cracking up as I was sure I had checked 'wedge', sorry to bother you. Psi (25 years ago, 17-Apr-01, to lugnet.cad.mlcad)
|
| |
| | Re: 2x3 trapezoid
|
|
"Simon Bennett" <simon.bennett@ntlworld.com> wrote in message news:GBxKIw.4zu@lugnet.com... (...) is (...) Try 6565 and 6564 - Wedge 3 x 2 left and right. Dan (25 years ago, 17-Apr-01, to lugnet.cad.mlcad)
|
| |
| | Re: 2x3 trapezoid
|
|
Simon, It's called a "Wedge 3 x 2 Left" or a "Wedge 3 x 2 Right". In MLCad, look under "Other Parts" and "W". -Andy Lynch ----- Original Message ----- From: "Simon Bennett" <simon.bennett@ntlworld.com> To: <lugnet.cad.mlcad@lugnet.com> Sent: (...) (25 years ago, 17-Apr-01, to lugnet.cad.mlcad)
|
| |
| | 2x3 trapezoid
|
|
Hello I have just got myself set up with MLCAD and I am drawing up all the MOCs that I have been unable to break down due to not wishing to forget how to build them but I have run into a problem which I hope this is the right place to come for an (...) (25 years ago, 17-Apr-01, to lugnet.cad.mlcad)
|
| |
| | Re: Printing parts-list
|
|
Thank you for the bug report - I will check that today and fix it for V2.00 Michael "Maico Arts" <maico@m-arts.demon.nl> wrote in message news:GB4p7x.2Ep@lugnet.com... (...) (25 years ago, 4-Apr-01, to lugnet.cad.mlcad)
|
| |
| | Printing parts-list
|
|
Hello (Michael?) I think I have found a bug in mlcad when printing the partslist. I am making inventory lists ofall my technic sets. I have build all sets I have, put them back in the boxes and added the extra parts. Using ML Cad I am making (...) (25 years ago, 1-Apr-01, to lugnet.cad.mlcad)
|
| |
| | Re: Printing problems in MLCAD
|
|
(...) I had essentially the same problem and found the following fix; Select 'Printer Setup' in MLCAD Select 'Properties' Check 'Scale to Fit' Check 'Scale to fit paper in printer' Then about three 'OKs' I don't know about others but this seems to (...) (25 years ago, 25-Mar-01, to lugnet.cad.mlcad)
|
| |
| | Re: Rotation trouble
|
|
Hey, There should be some buttons with arrows going around axes. These control the rotation of an element around the x, y, and z axes. The degree of rotation is determined by the grid icon. You can also edit the amount of rotation by going to (...) (25 years ago, 24-Mar-01, to lugnet.cad.mlcad)
|
| |
| | Re: Rotation trouble
|
|
Hey Dug, I have had some difficulty with that at times as well. One way I began to over come the problem was to open the rotation dialog bod and go to the bottom text window (you have to click the radio button to enable it). And enter "1 0 0 0 1 0 0 (...) (25 years ago, 24-Mar-01, to lugnet.cad.mlcad)
|
