 | | Re: LPub and Lsynth page for tracking enhancement requests and bug fixes
|
|
(...) Looking at the above list seriously..... You list a number of sub-model specific desires including: 1. view angle on a sub-model basis. You already have this using MLCad's ROTSTEP meta-command. ROTSTEP only applies to the file that contains (...) (20 years ago, 4-Oct-04, to lugnet.cad.dev)
|
| |
| | Re: LPub request
|
|
(...) The PLIST BEGIN SUB meta solution is fine. My problem was due to a lack of knowledge regarding LPub META commands. -Orion (20 years ago, 4-Oct-04, to lugnet.cad.dev)
|
| |
| | Re: LPub and Lsynth page for tracking enhancement requests and bug fixes
|
|
(...) My solution to the above is to give you explicit control over construction image render window size and PLI render window size. You can set these sizes small for test runs. Is this acceptable? It will be available in the next LPub release. (...) (20 years ago, 4-Oct-04, to lugnet.cad.dev)
|
| |
| | Re: LPub request
|
|
(...) I'm adding support for s and 48 in lieu of the pathing solution Lars' will be providing. If your flexible axle is produced by some known tool, I'm willing to add supprt for flex axle recognition to LPub. Orion, could you email an example? (...) (20 years ago, 4-Oct-04, to lugnet.cad.dev)
|
| |
| | Re: LPub request
|
|
(...) Hi Orion, I never got feedback from you about the PLIST BEGIN SUB solution outlined above. LPub recognizes parts synthesized with LSynth and tries to determine the part being synthesized. It recognizes flexible axles and determines the length. (...) (20 years ago, 4-Oct-04, to lugnet.cad.dev)
|
| |
| | Re: LPub mask generation
|
|
Hi Mike, As it turns out, my laptop hard disk died since brickfest. Please send me all relevent files and some background on how to recreate. Life has been very busy. Thnks for your patience, Kevin (...) (20 years ago, 23-Sep-04, to lugnet.cad.dev)
|
| |
| | Re: LPub mask generation
|
|
"Kevin L. Clague" <kevin_clague@yahoo.com> wrote in message news:I4EJ6K.154K@lugnet.com... [ ... snipped ... ] (...) California (...) converted to (...) list (...) Any luck chasing down the problem we were looking at at BrickFest? Mike (20 years ago, 22-Sep-04, to lugnet.cad.dev)
|
| |
| | Re: Converting Polyline to Mesh
|
|
(...) Err, no. That would have required some RTFM on my part, which seriously conflicts with the coefficient of laziness. Somebody turn off that firehose, pronto! (20 years ago, 21-Sep-04, to lugnet.cad.dev, FTX)
|
| |
| | Re: LPub mask generation
|
|
(...) I was looking too hard in the wrong place. I've got access to it now. I've installed the component, but I think I have to write a header file for it, so that I can use it under C++ builder. It looks very nice to use. I'm really looking forward (...) (20 years ago, 21-Sep-04, to lugnet.cad.dev)
|
| |
| | Re: LPub mask generation
|
|
(...) Do what? Get the source code, or use the png classes? At least for me, clicking on the link takes me to the sourceforge page for PNGImage, up left is a "Download" link which gets the .zip archive ((URL) I just downloaded it again, to make (...) (20 years ago, 21-Sep-04, to lugnet.cad.dev)
|
